Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi
I want to get external acceleration sensor values with SPIM using easyDMA on the sensor interruption (using GPIOTE). then after getting all data, I want to calculate...
Hello,
I have question, I'm actually developing an Android application and try to update the firmware on a device with a DFU process. It work on every mobile device except...
I am using the nrf51422 with softdevice 5144_2.0.1 ,
I set two network number using the "sd_ant_network_address_set" api , network number 0 for ANT+ cadence/heardrate.. network...
Hello,
I was just checking for differences between SDK v11 and v12, more specifically, the differences in the SPI HAL and driver code.
In hal\nrf_spim.h of the v12 SDK...
Hello, I am trying to write some data to the Nrf52, but all I get is a read only response on my phone. Is there any example how to write to the nrf52 tag?
I'm working on a custom bootloader; below is the step taken but it doesn't workout:
By using a working UART example, change the linker script:
MEMORY
{
FLASH...
Hi guys,
I am trying to use pstorage to store a temperature data inside the ROM. I have to use it as efficiently as possible so that 20.000 erase cycles should be enough...
If I want to set transmit power to -4dB, these are the settings:
command=LE_TRANSMITTER_TEST (this wouldn't be used anyway)
freq=0x3C (meaning: -4dB)
length=2 (meaning...
Hi,
I would like to store firmware version number at a particular offset from the application start address so that it can be retrieved by boot loader as explained here...
Are there plans to release the files for download instead of online-only access through the Infocenter? It was always so nice to have them on-hand to grep in the previous...
When I try to compile DFU examples, I get the following errors :
"..\..\dfu_public_key.c(20): error: #35: #error directive: "Debug public key not valid for production...
I have my custom board wired to the nRF52 DK. Using the SAADC example code located in GitHub I am trying to set up SAADC to measure the coin cell battery that will power the...
I am sending and receiving streams of data over BLE.
Do I need to add a checksum byte for every GATT write/notification/indication to ensure that my data is not corrupt...
Hello All,
I am interfacing nRF905 as a receiver mode which are interface with nRF51 DK.
As a transmitter used this module www.alibaba.com/.../RF-100m-transmission-distance...
