Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
I used the ble_app_lbs example as a template, with a PCA10003 eval board (nrf51422 chip). SD 110, Nordic SDK V6.1. Keil uVision 5.
I launch my application and my board...
Hi,
In softDevice S120 can we make second sd_ble_gap_connect on different peer, without waiting confirmation connect of the first one ?
Bests Regards,
Jérôme
Hi
NRF51822 with SD7, S110.
I have some troubles with DFU procedure. I uploaded standard OTA-DFU bootloader and S110 to my NRF. Everything works well with my code except...
Hi,
I was wondering if it is some easy way to turn off that the system goes into system off mode after a while for ble_app_pwr_profiling?
I would also like to test it...
hello everyone,
we're currently working with some nrf51822 beacons and throughout the project we recorded the antenna patterns of several of them. In the first batch we tested...
Hello.
I neet to write long characteristic value (250B). I use GATTS Queued Writes from example devzone.nordicsemi.com/.../ based on developer.nordicsemi.com/.../a00892...
Hello,
I am frustrated by a pair of nRF24L01+ communicating with each other, where all the Enhanced ShockBurst features are enabled.
The PRX is initialised as follows...
I could scan/detect Beacons, and I could update the configuration without any problem with the nRF Beacons app. The issue is that the configured Beacons are not detected in...
Hi,
I want to use the nRF51 dongle with the Master Control Panel.
I found in the nRF51 Dongle User Guide that the Dongle will run with the Master Emulator firmware, but...
I don't expect the Nordic engineers to know this answer but I'd like to hear from other devs out in BLE land...
Have any of you encountered truly horrible BLE PHY-level...
I am using S120 device to receive advertising from S110 device and need to get the exact time + sender's address information at Radio End Event.
I use PPI to start Timer1...
Hi,
I'v try to use the sd_power_system_off() and without successful.
The power consumption will be 200~230uA around.
My device:
Call the system off when ADV._TIMEOUT...
Hi
I am trying to make a ble central with s120 on a pca10001 board.
My problem is that it sometimes take a lot of time (up to 10 seconds) to find the client when i make...
Hello Nordic guys, help requested !!!
Error while connecting to USB port the new development boards, DK and DONGLE.
Error is " OS X unable to repair JLINK disk ".
...
Hi,
is it possible to use Nordic SDK with nRF51822 to have capacitive touch sensing with 2 dsital inputs, just as the mbed or avr library capsense?
MBED: developer.mbed...