I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hi,
Does the nRF51822 have a capability of responding to multiple phones?
I am working with RFduino using the RFD22301. I'm assuming that the RFD22301 is the same BLE...
Hey,
the nRFgo Studio contains a simulator for the nRF8001 and 8002. Will there be an update in the near future to simulate the bahaviour of the nRF51 platform?
Mar...
I have TIMER2 running at 500us interval. ANT is working as 100Hz master.
Understood softdevice will affect the timing and cause some latency.
I am guessing it is delaying...
Hi:
I'm implementing an controller for an open source drone Crazyflie ( www.bitcraze.se/.../) . My device is similar to pca10001 board.
Since Crazyflie is acting as peripheral...
Hi all!
I've been unsuccessfully trying to DFU the Smart Beacon Kit with the latest firmware.
Using the nRF51 DK and the TC2030 tag connect cable I was able to program...
I am trying to get a communication between two pieces nRF51822 using the my service. I checked the peripheral with Master Controll Panel app and is working fine. The multilink...
Hi,
I have the (IoT) environment running. The Raspberry Pi (with Miredo tunnel) is connected to the outside world. I can ping6 the ipv6.google.com server from Rasperry...
Hi Team,
I am using nrf-51 DK as sniffer.
I need some guidance regarding how to study or analyze these packets?
I don't know what exactly I should check in each REQ...
Hello,
I am working on nrf51822, My requirement is to upgrade the firmware over the uart with help of DFU.
I have made code for that on controller side and fortunately...
In the release notes of the nRF51 SDK v8.0.0, section "Supported devices" it says that "This SDK is optimized for IC revision 3".
I am using a Laird BL600-SA-04 module...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Howdy, I'm trying to DFU my 51822 beacon v1.1.0 with MCP. MCP is failing the transfer. Steps I have taken are:
-Programmed my beacon with segger from the dk, both the SD...
There are apparently only 3 S120 examples available, and one of them is a peripheral example, which can be done with the S110, so really there are only two examples. This...
Hi,
I tried to run example: ble_app_multilink_central_s120_pca10028 but application goes to HardFault_Handler when it reaches sd_app_evt_wait() (in power_manage() function...
