Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
Hello,
I am working on pca100028 and using s130 softdevice(SDK 6.1.0.0.). I am trying to see UART log on pc. But my code get stuck at the following while loop.
void simple_uart_put...
I am using ATmega32s to drive the nRF24L01+ chips and a low dropout 3.3v regulator (TI’s LP2950) to power the nRF from the five volt buss.
Both the transmitter and receiver...
We are seeing bonding issue between Nexus 6 and our 51822 based product. After inspecting the sniffer capture, we observe that the phone advertises its IO capabilities as...
I have an nrf51822 S110 based application that tries to discover the primary services on the GATT server at every connection of a central.
Unfortunately, the central does...
Hi,
I have read all the answers about ANCS, it seems there is no conclusion can be resolved the problem, that is "It seems working first connection. But after rebooting iOS...
Dears:
I'm using nRF51822 with softdevice S110 . And I want to know, how can I switch the communication mode betwean BLE and 2.4 G ?
If possible, could you provide me...
According to ble specification [1] and based on my test with iOS, the cts_c library seems to have bugs on a process decoding adjust reason data.
Here is a simple diffs...
Hi,
I want to run the experimental_ble_app_uart application on our custom nRF51822 board.
However, I could not find a proper bootloader to start the application. Is...
Hello everyone,
I have a nrf51822 dev board which cannot program because of Keil is giving me errors which I detail here.
I'm using Keil uVision 5.14 and as you can...
In my current design, for the schematic and layout I've copied the design of the first version of the usb-stick with meander-antenna and matching network/balun. In the later...
Hi,
I have been programming PCA10028 using these commands for a while without any problem:
$ JLinkExe -device nrf51822_xxaa -if swd -speed 4000
J-Link>loadbin s110_nrf51822_7...
hello,
I am using S130 softdevice in nRF51822 DK. I made one device as peripheral and other as central. My peripheral is acting as GATT client and central as GATT server...
Hi everybody,
I test the pstorage library. But it didn't work. I print the result with uart, as the image shows. But as you see, It has some problem. And I have no idea...
Hi sir
If nRF51822 unexpectedly enter DFU OTA mode, did boot loader have timeout counting to exit DFU?
Besides, if nRF51822 entered DFU mode and didn't update new firmware...
Hi all,
This 60-second limit is not enough for us. Our application is 48 kB & takes 35 seconds to upload. It should be enough, but the problem is that our iOs app does...
