Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
Hi,
Does Nordic Semiconductor provide any resources (codes, macros, documents) for work with IAR or Keil's simulator to fully simulate nRF51822's peripherals?
Thanks...
Hi,
I do:
err_code = ble_bondmngr_bonded_centrals_delete();
APP_ERROR_CHECK(err_code);
till now all is ok.
But when I do:
err_code = ble_bondmngr_whitelist_get...
Hi,
I need to delete all centrals using ble_bondmngr_bonded_centrals_delete ble_bondmngr.c function. It is working but it is not cleaning the whitelist.
So, when I do...
In the example of hid_mouse, ble device will bond master when disconnect event happen.
I try to add this two codes to Implement my idea.
err_code = ble_bondmngr_bonded_masters_store...
I write this code to set my ble device power down,but it causes reboot without any error report.
GPIO_WAKEUP_BUTTON_CONFIG(LEFT_BUTTON_PIN_NO);
GPIO_WAKEUP_BUTTON_CONFIG...
I try to use 51822 to run ANCS sample(ble_app_ancs). It work well and I can get notification source and notification attributes. But I don't see any source code for get App...
Hi
I've a reproducable behavior i'm not able to explain. I'm using the softdevice S110 6.0 on a nRF51822.
The firmware implements some BLE profiles and uses TWI Master...
Is there a way to map external memory (SPI connected) to force the app to start execution from there ?
If not feasable , there is a way to transfer the execution from internal...
I have a 51422 board design and I just got Ant-FS working with our firmware so I can now download data from an external SPI flash to a desktop application.
I want to be...
Hello:
I am using NRF51822 to design somethings. And I want to use interrupt send method instead of polling send method.
NRF51822's UART0 provides TXDRDY interrupt. After...
Hi,
I have tested the nRF Toolbox proximity application using nrf51822 evaluation kit and with nexus4 smartphone it is working fine. Now my question is, is it possible to...
Hi
I am trying to overcome the problem that I have confronted, I have no buttons to delete bonds. So instead of deleteing this is what I did.
I modified the bondmanager...
I am developing hid_mouse . When I connect Android once and ubond hid_mouse I must set bluetooth off and on again to connect ble device otherwise it will connect again to...
Hi,
I am trying to set a value in the NRF_POWER->GPREGRET when softdevice is running, but it doesn't work. I don't get any error, but the value is always 3 and not 1 like...
