Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi,
I have a nRF52833 DK which contains PCA10100 debugger on it.
However, examples in the nRF5SDK160098a08e2 SDK seems like not supporting PCA10100.
Which example...
Hi all, I am beginner to Bluetooth module interface and I am in the stage of implementing the software for Bluetooth module to start and visible to other Bluetooth device...
Hi,
Lookin at this ticket https://devzone.nordicsemi.com/f/nordic-q-a/32090/qspi-pin-mux-on-nrf52840 for the nrf52840 it is said that it is ok to put QSPI on any pins (depending...
Hi,
I need to use cJson library to parse some json data. I have seen that the library is located at "nrf\ext\cjson" path. I have also seen how to add that library to a...
The documentation is VERY difficult to search. A search only goes over the chapter. I get different results depending upon which one I am in .... aarrg! And there are SOOO...
Hi,
I am not sure about the functionality of notify_cccd_handle.I am sending data from central to peripheral so the central should receive a notification from peripheral...
Very similar to this post , my use case involves cycling the modem between online and offline ("AT+CFUN=1" and "AT+CFUN=4"), for enabling GPS and also for reducing power consumption...
I am trying to broadcast an advertisement packet from a Nordic board nrf52840.
I have downloaded the latest nordic sdk and am loading the ble beacon example to the device...
Hello Nordic team, I'm currently developping a project that uses the nrf52840 as an HTTP server/client on top of its Bluetooth functionnalities.
I'm looking into implementing...
Hi,
I'm currently wprking on my project, my project it's about swarm, before the master swarm can advertise the message to the slave swarm through blehandler function now...
Hi,
My unit based on NRF52832 with SDK11 and works as pheripheral.
I started my project from nordics NUS (Nordic uart service) example.
My IOS software developer wants...
Hi Sir,
We got the nRF52833-DK, and tried to program the nRF52832 IC through the nRF52833-DK.
We download the latest version of nRF connect and command line tool, but...
Dear,
I am using THINGY:91
I am trying to read the data from BME680 sensor:
1. config: ( i used conf file from asset_tracking)
and, get the temperature:
...
Hello,
I am using UART1 to communicate with sensor. It is working fine. I can receive the data. Now I want to modify this data. When I use strcpy() function, it works properly...
Hi Team,
We are trying to make Nordic NRF52840DK board to act as a server (BLE ) where as we are trying to connect other board (Not the Nordic chip) has only transmitter...
