hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi, has anyone interfaced with the SX1272 using the nRF52840? Perhaps they could point at us some LoRa SDK or libraries which will help the development process?
Thanks
Would a wire-wound inductor work better than a chip inductor for the antenna circuit of NRF52810? I'm using the 32 pin QFN package with the LDO configuration which calls for...
I need to calculate the max number of concurrent connection Central can support given the following
Connection Internval = 7.5ms
Baud Rate per connected peripheral:...
Where can I find this version of hub?
ERROR: Could not find a version that satisfies the requirement hub==2.0 (from -r zephyr/scripts/requirements.txt (line 10)) (from versions...
When nrfutil is installed with python 3, I get an error when generating bootloader settings page. This does not occur with python 2. As python 2 support expires very soon...
Hi.
I am testing MESH by nrf5SDKforMeshv201src and nRF5_SDK_15.0.0_a53641a.
I have a problem.
My project have one of the client and one of the server.
Client transmit...
Hi I had a question to setup the MCP2515 driver in the zephyr project.
We have a custom board for the decawave DWM1001 module, which uses a nRF52832 chip. They have a device...
Hello I am using a I2C sensor module and I need to tranmit only address to receive data back, but I dont know how.
Program crashes on line 4.
Thank you for your help...
I have a DK52 with another device at attached to the SPI bus. I also have a PPK. Should
I connect the second device to VDD_nrf to count as a load? right now it is connected...
When the bluetooth service function is initialized, sd_ble_uuid_vs_add() is called in the ble_dfu_buttonless_init() function in case of an out of memory error. In the ble_nus_init...
Hello, Is there any evaluation kit available for NRF905? I found this one online but DIGIKEY website says its obsolete::
media.digikey.com/.../nRF905-EVKIT_PS_Rev1.0_Jan2004...
Dear Nordic staff and users,
Now I'm trying to confirm that my local LTE operator supports energy saving modes. It went with flying colours with PSM:
at+cereg=5 OK at...
using SEGGER Embedded Studio for ARM V4.30a, I get a problem of Linking with an nRF5_SDK "blinky" examples. See hereunder the error message:
Seem to be a problem of configuration...
Hello,
I can create a zip file with nrfutil pkg generate and there is a bin file in it? I want to make DFU as a bin file only.
I only want to download the firmware as...
