In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi,
I want to know that what is the different between RS232 and TTL.
I want to know that can we two RS232 to TTL converters back to back in the wire ??
Hi,
I'm using nRF52832 Software Development Kit, PCA10040, S132.
In nRFgo Studio, I erased all my SDK.
In nRFConnect, I selected serial port which SDK connected.
And...
hello there i am using nordic SDK 10. spi_master.rar (/attachment/5a7f162df5ffa9d40019ed2553d99f1d)
i am getting some compiler error. i have uploaded text file. can anyone...
I am able to run nRF5_SDK_12.2.0/examples/peripheral/blinky using the armgcc toolchain without any issues but any example with a soft device enabled (e.g. nRF5_SDK_12.2.0...
Hi. I'm using nRF51822, SDK12.2.0, S130 v2.0.1.
I'm trying to make a peripheral device using nRF51822.
Is it possible to define multiple Characteristic Properties? ...
Hi,
My code was working perfectly until yesterday, where the function "ble_nus_string_send" on my main loop started returning NRF_ERROR_INVALID_STATE because "p_nus->is_notification_enabled...
Hi,
I have found that the sdk13.0 is support 20 current connections , I test it by using example /SDK13.0/example/ble_central/ble_app_multilink_central , I change the central...
Greetings Nords,
total noob here,
I've got two preview nRF52840 devices (as well as the two normal nRF52 devices),
I want my two preview devices to be able to ping each...
Hi,
I am using nRF52 and SDK13 with SoftDevice 132 v 4.0.2 which is now supporting multi-peripheral connections.
I am using multi-peripheral example for reference. In...
How to make BLE examples working. for nRF52DK series (BLE_app_template)?
Hi, I tried for around a week. and I will describe what I did, and what I have found first.
I...
We have IoT gadget, where we use coin cell (CR2032) as power supply. Now, we would like to connect U_bat directly to ADC to measure battery level every n minutes, but keep...
Hi.
I have an NRF52DK Board. With the built in JLINK Debugger it works fine. Now i bougt an KEIL ULINKpro Debugger. Is connected with the 10 Pin cable. And i cannot flash...
Hello.
I'm working this : github.com/.../pc-ble-driver
In Chapter: Compiling the connectivity .hex files
2.Apply the patch hex/sd_api_v/SDK_connectivity.patch from...
