pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I'm trying to use nRF51 IoT SDK and setting raspberry pi as router.
When I enter the below command for connecting to nrf51, wlan connection is disconnected.
echo "connect...
My configuration:
NRF51822 v2
TWI
GPIOTE
Issue:
The gpio interrupt does not get triggered. I know that my twi device is changing the state of the gpio3...
Hello, I apologise for this being quite simple as questions go but I was wondering if anyone knew where to begin or if there is any good information out there on how to use...
Hi,
I need use the nrf51822 to connect to PC via usb ble adapter (virtual com port).
The PC side has the USB BLE dongle (adapter).
http://www.amazon.co.uk/Plugable-Bluetooth...
Hi....
Is there any issue in sending a value on a character in button_event_handler? When i tried it disconnection is happening.Am not using button service , just using...
When running the makefiles found in the esb/gcc_rx and esb/gcc_tx folders I get the following errors:
base:gcc_tx jnoble$ make
mkdir _build
"/Users/jnoble/hardware/nrf51822...
I have trouble compiling successfully even the simplest of example codes for the nRF51822 with the Keil MDK-ARM toolchain (v5).
For example, for the "blinky" project, I...
I have ported the example ble_app_beacon from sdk 7.2.0 for use with nrf51422_xxaa and softdevice s310 (v.2.00).
In the function ble_stack_init() there is a call to the...
Hello everyone,
I have two doubts related to pca10001 board:
What is the maximum amount of current
that can be pulled from a single GPIO
pin?
Does the...
Hello,
I just received new rev.3 nrf51822 chips, so I am migrating with my project to newest SDK version.
I installed Keil5 with that smart run-time environment manager...
I would like to send the current status of the battery as a beacon.
ADC and a few resistors and what do I need?
I am currently using nrf51822.
I know nrf51822 to...
I'm trying to port my old project to the newer soft device and SDK (v8.0.0) and just ran into an issue where the app_timer_event_t seems to no longer be defined. My previous...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Is there a UART version of the DFU example that is provided with the new SoftDevice 7.0?
If not how to go about modifying the BLE DFU example to be able to handle UART...
