Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Dear all,
I've loaded this example github.com/.../Blinky_ble
into the nrf6310 as it is, and s110_nrf51822_7.0.0 as a softdevice
I am connecting to the module through...
I need the nRF51-DK-HW hardware files ，but without a product key.
And I cann't buy a nRF51 in CHINA.
Someone can give me a product key or
help me to buy a nRF51.
Thanks...
Hello everyone,
I have developed a firmware that makes accurate time of flight measurements, working with my own protocol.
Now I need to integrate this firmware with BLE...
Hi,
We would like to switch to a stand alone debugger for nRF51822, However in the product specs ( www.nordicsemi.com/.../nRF51822 ) mentioning that standalone programmer...
Hi guys,
I have nRF51822 Evaluation Kit.
I am trying to make simple project for my senior design.
Here is the setup.
I need to control simple on/off switch from...
Hi, I'm developing a BLE application.
I want to send multiple packets (from same characteristic) per connection interval.
I've read this question:
devzone.nordicsemi...
hello,
I am trying to develop an application using s130 softdevice on NRF51822 board.
i am able to do a undirected adverisement after a scanning. But when i am trying...
Hi
I use proprietary service to transmit data between iOS and nRF51822. The example I referred to is below.
C:\Keil\ARM\Device\Nordic\nrf51822_v6.0.0.43681_Backup\Board...
Hello,
I need to send packets on a specified advertising channel and receive them at the same advertising channel. Unfortunately, the SoftDevice API does not seem to support...
Hi,
I have several nRF51822 which are far away from each other and I want to communicate with all of them without need to go to deferent places to get the signal.
Does...
Hi
What is the scan interval ,while using the nrf51822 dongle as nrf sniffer.Is it possible to change this interval or is there any option provided in the sniffer api ...
Hi, we are using the nRF51422 and the s310 soft device using the 5.2 SDK.
In ble_error_log.c I noticed that you have a comment suggesting that write to flash was removed...
I have already installed nRF51_SDK_7.1.0_372d17a_packs. The examples in this SDK are only for nRF51422. Can I use these example in nRF51822 by just change device to nRF51822...
I was going through the figure 10 of page 35 of nRF24L01+ product specifications and found that when an ACK is received, it checks for only ACK payload. Does it mean that...
