Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
I have TWI sensor comms running fine in Zephyr on nrf52840_dk and separately Bluetooth controller in low latency mode using S140 softdevice also running fine in Zephyr on...
In SDK For Mesh 4.1.0 the Light LC/CTL/Lightness models were added. The problem with this addition is that another flash page is reserved for the models metadata and possible...
Hello,
I am trying to send something by my own via UARTE0. This is only for testing/learning purposes:
This is what I see:
[00:00:00.000,000] <info> app: enable...
Hi,
Can I control warm light as well as cool light using the CTL+LC server example provided in the Mesh SDK v4.2? Or does it support only warm light?
Moreover do we...
This is my log
Loading solution asset_tracker.emProject Executing load commands cmake -GNinja -DBOARD=nrf9160_pca10090ns -DBOARD_DIR=C:/Workspace/nRF9160/ncs/zephyr/boards...
Hi,
Currently I am setting up my work environment. I have a simple Zephyr project running on our custom board with the nRF52840, so a modified example and a custom board...
Hi Folks,
I am currently working on a BLE configuration composed of two NRF52840 chips. One is configured as central and the other as peripheral and use coded phy (long...
While I am going to pair with my android 9 Asus mobile phone with SDK 17 nRF52840. It in my mobile showing "Pairing rejected by Nordic_HRM". After that I have added a some...
Dear community,
I am trying to implement a custom service, however I am struggling because many example codes are for PCA10040, Softdevice S132 and/or for older SDK's. I...
Would it be possible to get the SHA256 hash for version 5.1.0 of the S132 soft device for the nRF52832? Just want to verify the integrity of the download. Thanks.
Hi All,
I am currently designing my PCB using nRF52840 chip.
I was using the footprint downloaded which was in nRF52840 dongle pcb library given by Nordic. During DRC...
Hello,
I am using Nrf51822.
I am using sd_110/application/bootloader, etc. in SDK_10.0 without problem.
Recently, migration to SDK_12.3 / sd_130 is in progress to...
How wide are the peaks? I know that it depends on many factors how high and long the peaks are. Currently we have measured peaks of 450 mA for 40-50 ms in our application...
Hi,
I am trying to run the Zephyr BME280 sensor sample application (using nRF9160 DK) in NCS1.3.1, but get the below error:
My prj.conf is as follows:
And board...
Hi all:
I install "nRF Connect SDK v1.3.0" by Toolchain manager,
but it always show "Failed to clone the repositories".
Could you have any suggestion?
best...
