Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi
We are using NRF52 and SDK 11 and S132.
The nrf52 acts as a central and selectively connects to the closest phones (ios) that are acting as a pheripheral.
For this...
hello,
nordic's engineers, need your help.
(1) the first problem : can not set VDD output to 3.3V
From nRF52840_Product_Specification_v0.5, it says:
High voltage mode...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Hi. I'm using nRF51822, SDK12.2.0, S130 v2.0.1.
I'm using nRF chip as Multi-connection Central and 1 Peripheral as well.
My event function is
static void on_ble_evt...
I've tried everything I can find on this topic and I still cannot get P0.09 to behave as a GPIO pin. Does it have something to do with the way I'm attempting to initialize...
Hello,
I am working on a custom PCB with a nRF52832 and I've been unable to get the ON IDLE power under 480uA. Here are the basics regarding the setup
nRF52832 Rev...
Hello! I'd like to know if S132 v3 implements the frequency hopping scheme defined by BLE.
I've read some documentation on Gazell, but from what I understood, that is a...
Whenever our battery runs to zero, or if we have a reset due to voltage droop, the unit will not auto-connect and the user is forced to "forget" the device in iOS bluetooth...
Hello,
i'm trying to use nRF UART driver (nrf_drv_uart) to implement a high level UART manager.
I followed indications on SDK documentation but it doesn't work and i think...
Working on a project to set up a bidirectional UART to SPI link over ESB with nRF52832 (PCA10040), using SDK 13.0.
Working from provided examples for PTX and PRX, I manage...
Hello,
I've implemented one custom service very similar with NUS. I have two peripherical devices that are running in two PCA10040 with S132 12.1, and one central device...
I have set up some code using the ESB example in SDK v12.2.0 I and am able to transmit and receive packets between two nrf51 dongles, with no issues. However, when I program...
Hi,
I did time measurements for packet transmission (notification) and saw only ~ 30 microseconds (about 1000 ticks with 0 prescale) difference between sending one or up...
Hi,
I am using nrf51822 chip. I am using RTC to generate irq with CC. Everything works fine for IOS and old Android version. New android version makes 2 things when I disconnect...
