SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I am using nrf_serial in IRQ mode to communicate with an AT based device. When I reset the device using ATZ, I get NRF_SERIAL_EVENT_DRV_ERR -- likely because the pins go into...
Dear All ,
I am finally able to get my beacon app to compile and work on the nrf51822 using keil with s130 softdevice.
I tried to add service data to the advertising...
Hi,
I have a situation where I have to create 4 TWIS instances on nRF52832.
sdk_config.h only shows 2 TWIS instances.
Is it ok if I add other instances (TWIS2_ENABLED...
Hello,
I was testing output on a GPIO pin with the mesh/dimming_server example and was only able to see 1.6V when measured.
I read through the example on infocenter...
Dear All,
I thought i wrote this question but seems it did not get registered. We are using the Beacon App from sdk 12.3 with the nrf51822 chip on custom board. I have...
Hello, I'm still a beginner with mesh so excuse me, if this might be a silly question or has been answered before. I did not find a post that quite resembled my problem. ...
I'm trying to use some code from the sample files and given libraries to create my own custom program. Upon startup, this is what I get:
Here is the only function called...
I am Currently under process of evaluating various modules for implementing BLE Mesh, Had few concerns regarding the same, would be great if someone can clarify upon them...
Hello,
I have seen today that the new releases of the v1.0.0 SDK and v1.0.0 modem firmware were release for the nRF9160 DK. I have been able to update the modem firmware...
Hi,
I am trying to migrate my project developed on Mesh SDK V2.0.1 to V3.1.0. I followed all the steps you recommend but i am stuck with the configuration of my server node...
hi all ,
i run Serialization application between nRF52840-DK ,it not start up.
how to Debugging this issue? i have been reset connectivity board,the error message halt...
I am trying to connect the MS5611 ( https://www.te.com/usa-en/product-CAT-BLPS0036.html ) using the GY-63 Sensor Module to the n RF52840 with the nRF5_SDK_15.3.0_59ac345 SDK...
Hello.
I would like to know which PCB surface finish would be used for bluetooth application. There are HASL, OSP and ENIG. nRF51822 IC chip and PCB trace antenna will...
Hello All,
We are designing a Tracking device system, for this we use nRF9160 LTE+GPS combo module. this system is battery operated so we need to monitor the battery continuously...
Hi,
I've been trying to lower the power consumption of the MQTT example and followed the guide in here .
1. I compiled the low power UDP example and do exactly all the...
