[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi,
I have 3 of nRF52840 boards, SDK V2.2.0 and nRF SDK V15.0.0.
I already tested the light switch control example, and saw it working with one client and 2 servers and...
Hi Nordic,
I have added new files to my project and added their path to user include directories of common configurations. When I build I am getting this error "No Source...
On my macOS Mojave, I have followed the 'Getting Started Assistant' in setting up the development environment for the nRF9160 but I am unable to load the asset tracker project...
Hello,
I am developing firmware for nRF52810 with SDK 15.0.0 and I need the OTA DFU features (buttonless DFU to be more specific) but there is no DFU demo for nRF52810....
Hi,
When trying to drive a motor driver, my nRF52 DK board is damaged with power rail 3.0V dropped to 0.5V.
After I desolder the interface MCU, the supply comes back...
Hi,
What is the limitation in terms of the number of bytes that can be sent over the UART to be sent over BLE on the usart ble example? I tried sending 32 bytes and it worked...
Greetings,
I am working with serial mesh (nrfSDk 15.2 for mesh 3.1 with softdevice s132_nrf52_6.1.0) .
1. I followed the serial example available and its working.
2...
Env: nrf52, sdk15, ubuntu, SES
Hi First steps on fstorage. As I just need to store and read an array of some bytes I have chosen fstorage
and I got this as output...
Hi,
I am working on DFU over Mesh for quite a bit now. I did run few tests but never run the DFU on a large network comprising of 100+ nodes. SO, I have questions about...
Hello
We are trying to finalize the layout we need for a nRF9160 module with gps capabilities.
I have downloaded the schematics and layout for the devkit V0.8.5.
what...
my code based on file "nRF5_SDK_14.0.0_3bcc1f7.zip".my hardware based on nrf52832QFAA.
my options set as:
project “bootloader_secure_ble”：
project “ ble_app_hrs ”with...
I changed the bootloader size by changing the flash start address (in the .icf file, from 0xf8000, to 0xf7000). I just want to check what other files/settings needs to be...
I need to use pin 8 and pin 20 as outputs on the nRF52 DK, to be transferred to a custom board built with the nRF52810. I'm using SDK v15.x.x.
I need to drive PWM output...
Im trying to detect power off. The signal power off looks like:
The time to get 0V equal 15seconds. GPIO EVENT and COMP do not see changes in the voltage level, they are...
