Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
On nRF52, I see that 100 kHz gives a SCL period of 10 us which is correct but for 250 kHz, I get 8 us instead of expected 4 us. Similarly, for 400 kHz I only see 5 us instead...
I have a case where a module that can perform bit clears in the UICR needs to execute while a Soft Device is present and enabled.
I am aware that any direct flash access...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the soft device to work as s130 for its (simultaneous Central/Peripheral...
Hello!
I'm trying to read data off of a commercial blood pressure monitor (Qardio arm) using an nrf51822 with the nrf51 SDK v10.0.0 as the central role (s120). I am able...
Hi,
we are using nRF52832 and running into memory issues as we add functionality.
It would be great if the '40 was available as a drop in replacement in WLCSP package...
Hello.
I want RSSI check. so added source code as below.
test_rssi_start = sd_ble_gap_rssi_start(m_conn_handle,BLE_GAP_RSSI_THRESHOLD_INVALID,0x00);
if(test_rssi_start...
Hi all,
Is possible using NFC to send variable message? I want to send a counter event (data I got via BLE) to the NFC module.
Using the example I was not able to do...
Hey,
I'm just wondering how to add a UUID to the blinky example peripheral?
I want something like the heart rate sensor where its advertising BLE_Heart_rate_sensor.
I...
We have recently migrated from a custom board based on the nrf51 to a new board with the nrf52832. Our nrf51 board used to run at 6-8 uA when it was just sitting there advertising...
Hi
During schematic design, i read regarding proper powering of NRF52 (the product is battery powered 2xAAA). somehow i can't find this info now and i would like to verify...
What does mask and 1<< mean in the following code:
#define BSP_LED_0_MASK (1<<BSP_LED_0)
#define BSP_LED_1_MASK (1<<BSP_LED_1)
#define BSP_LED_2_MASK (1<<BSP_LED_2)
...
Hi all,
I'm transferring data to and from an Atmel AT25040 NVRAM using SPI, and it works perfectly when run within main(). However, if I run the same code from within an...
Hi, I want to enable notification for a specific characteristic, and to do that, I must write 0x01 (in java it's going to be "01,00" ) to the CCCD handle of this characteristic...
Hi,
I tried to use python API to drive the nrf sniffer to capture ble device information by their advertisement packet. I can successfully target a specific ble device...
