Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I am working with the NRF5340 to develop a BLE audio streaming application using a PDM MEMs microphone.
I have played around with the NRF5340 Audio DK and got PDM audio...
Hi
So the central multilink example uses init_scan . connect_if_match = true ; Mine is false, because I want to manage the connection myself.
I'm filtering out 5 seconds...
I am trying to debug an application in VS Code for the nRF52840 DK in the nRF Connect SDK.
After starting debugging, I immediately get this error: "Exception has occurred...
Hello sir/Madam,
i want to change the code that prints values(the values are from nrf_dm sample) to the serial terminal in nrf52840 dk using nrf connect in visual studio...
It is not possible to connect to the Peripherial using identity address steps to reproduce 1. connect to peripherial using random mac address 2. bond using random address...
I'm currently working with a BL5340PA module with the external antenna connector. we were wondering what was the RF switch isolation between the two antenna outputs. In other...
Hello,
I am currently working on a project using a custom board with nRF52840 + nRF21540 . I am trying to measure wireless performance using Direct Test Mode (DTM) , but...
Hi, when I use OTBR to commission a matter bulb(52840DK), I found this log:
I: 7371 [DL]CHIPoBLE connection established (ConnId: 0x00, GATT MTU: 247) D: 7448 [DL]Indication...
Hi,
I have been trying to use the radio_test example application to try and accomplish my goal but no success so far. My goal is to be able to compose an advertisement packet...
Hello, we would like to use the 4th reference circuit with the QIAA footprint from the Nordic nRF52840 chip's datasheet. However, in our PCB design, can we change the placement...
Hello,
I'm attempting to write to a ble characteristic but when i call bt_gatt_write, I get BT_ATT_ERR_INVALID_ATTRIBUTE_LEN, I have tried to send the same command using...
Question: I am working with the Ebyte E73-2G4M08S1C module, which is based on the nRF52840 . The module provides D+ and D- lines . Can these lines be used for debugging and...
Hello,
I'm trying to put the nRF54L15DK into System Off mode, using sdk & toolchain version v2.8.0.
The provided example (\samples\nfc\system_off) works on my evaluation...
Hello Team, We are currently building a circuit using nRF52833 QDAA QFN40 ( Configuration 5). We would like to know if there are dedicated pins to be configured for BOOT as...
