In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi Sir,
In the datasheet of 52840, we know the DEC1 is 1.1V, DEC2/4/5 are 1.3V, DECUSB is 3.3V.
When measuring these pins, we may not get a precision value, like we got...
Hello,
I am developing an application to scanning a device continuously in nrf52832 chip. My concern is that when the device scan the other peripherals it consume a lot...
Hi,
Can you please give a brief idea which softdevice and SoC we should use as per our requirements.
1) The device should be able to connect to the mobile phone(mobile...
I am not able to build in release mode where as in debug mode builds. Even when option for release is chose , it builds in debug mode. I am using Segger Embedded studio 4...
We are using a BLE module EYSHSNZWZ from Tayio Yuden which contains the nRF52832.
using SDK 15.0.0_a53641a and Softdevice and Softdevice s132_nrf52_6.1.0
The application...
Hi,
Recently I degubbed issues on debug mode for an application on segger embedded studio 4.1.2. Now I see in release mode some kind of errors is happening, it works well...
Hi,
I need to use a custom board with old nRF51822 rev.2 (QFAAG0). The compatibility matrix indicates S110 Softdevice SD5.2.1. I found only 7.3.0 or 8.0.0 and there is no...
hello
i need a device capable to work with Bluetooth 5.2 to transmit audio
is nrf52840, nrf52820, nrf52832 or any other support Bluetooth 5.2 and has Protocol stack...
Hi community !
i put the same question here but with less explaination : https://devzone.nordicsemi.com/f/nordic-q-a/61393/mesh-uart-coexistence-communication-with-pc I...
I am evaluating if I should change to nRF Connect SDK for a new project so I have been updating nRF Connect to latest version v3.3.3
I have installed Getting Started Assistant...
Hello, We are developing a application that sends some data to AWS in some intervals(3 - 15 minutes). This application were currently being tested on custom nrf9160 boards...
Hi,
I am using nRF52840, S140 V7.0.1.
I am using Secure Serial Bootloader and able to do DFU of Application.
Now I am trying to do the same for generating SoftDevice...
Hey everyone, I have a device that's in production and everything is working great, however we have a customer that is creating their own software to interface with our sensor...
I followed the instructions "Programming applications through USB" to update the firmware on the nRF52840 SoC. I pushed down the SW4, switched on power, released SW4. "No...
