Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hi everyone,
I was looking at the SAADC example and I need to modify it in order to fit my design. I want to perform analog readings from eight sensors using an eight-channel...
Hi,
I'm developing a BLE application that is also using FreeRTOS.
I also need to use PWM to control an LED (mainly because the requirements define LED patterns, which...
Base BLE structure ble_advertising_t contains a member structure ble_adv_mode_config_t. This structure contains two parameters that are meant to limit number of advertisements...
Hi Team,
I want to create on flash section to store the specific data like Crypto Keys and Serial numbers. How to create one page/section in existing Flash memory without...
I am trying to test a BME280 sensor on the nRF9160. I followed the steps where I created a folder (board) and added the nrf9160_pca10090.overlay and add couple of line in...
Hi, I would like to implement free rtos on nrf 51 using IDE Segger Embedded Studios. Could some one please direct me to the necessary links/ information.
I have researched...
Hi ,
I am working on project which is based on nrf9160 Development board.
could you please verify these points-
1. I am sharing the snapshot of the registers...
I have downloaded the Keil compiler and the Nordic key for same.
When running Keil_v5/UV4/PackInstaller.exe I can not get the update:
Cannot download file developer.nordicsemi...
Good Day,
i´m want to use saadc with 7 channels. I´m using the ADC Driver with an interupt handler. All 10ms the sampling starts per cpu. I use the configuration followed...
Hello,
I am running on a NRF52840 DK a Zigbee program configured as a router. For the coordinator i am using the cli example from the SDK.
On the router, I have developed...
Dear Nordic Semi, ladies and gentlemen!
I'm working on a prototype device with USB host functionality. I am using Arduino USB Host Shield connected to nRF52840 DK . DK is...
Hi，
We want to confirm the effect of GPS fix_interval and fix_retry, so we start GPS with parameter fix_interval=10s, and fix_retry=30s, then get the result as the following...
I try to bonding.
Using SDK 15.3. 0 and S332 Softdevice.
I successed bonding procedure used Peer manager.
after bonding, If I try to connect one more, nRF Connect app...
Hi, I can not connect to nRF52833 and nRF51 after I return from Flight mode on Android devices. I am keep getting Error 133 (0x85): GATT ERROR. I am using the nRF Connect...
