Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi
I followed below tutorial with my nrf52840 using SDK 15.3.0
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a...
Here is the software: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer-for-Bluetooth-LE which notably doesn't support the nRF52 dongle
I also...
SDK15.3
nRF52840
S140 v6.1.1
Q1. I have an RTC compare event connected to a Timer count task over PPI. The Timer is configured in low power counter mode. My question...
Hi, I am strugling to get the power comsumption down to the number I have been reading on this forum. I followed the instruction of the dev kit manual . When measuring the...
Hi, I'm getting regular crashes with my app: SOFTDEVICE: ASSERTION FAILED. Using and NRF52832, SDK 15.3.0, SD 132 6.1.1, and Mesh SDK 3.1.0. With DEBUG defined, I don't really...
I'm trying to interface 2 SPH0645 mics to the nRF52840 DK.
Little did I know when I bought them (the mics) that you need to waste 2 timers + 2 pins + memory space to make...
Hi,
I am trying to measure a signal using the SAADC driver on SDK 13. I have used the example from the nrf52 playground for low power ADC
I have a few questions on best...
Hi,
I have a nRF91 development kit and want to connect P4 to the Segger Jtrace for ETM streaming. In the manual, it stated that a 2×10 pin 1.27 mm pitch surface mount connector...
Hi,
Is there any way to get network time without previously setting it with AT+CCLK?
I would like to implement sort of "fake time" by initialising it with the network...
Hi, I'm struggeling with this stage on the "getting started assistant"
"Clone the nRF Connect SDK"
Is there any step by step video to help me do this, I have probably...
I have one service with multiple characteristics(11). Out of 11 characteristics I have 7 characteristics which have notify as their attributes. So when I select the notification...
I have been using nRF9160: LTE Sensor Gateway to send data from nRF52832 to the cloud. The nRF9160 is subscribed to nRF52832 and hence gets updates after every certain period...
Hi,
I'm trying to use Power Profiler Kit (PPK) with nRF52 DK to measure the power consumption of our custom hardware. My setup is as described below: - The PPK is connected...
SDK:15.2
IC:NRF52840
Hi，When I upgraded the device using usb dfu, after entering the app, there will be an additional current of about 180uA（Sometimes appear）.
Both...
Somehow my nRF9160 DK board has become essentially unresponsive. Flashing new modem using nRF Connect Programmer, and downloaded nRF FW, "seem" to work. But nothing else....
