I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello. I have integrated signature validation before boot in my boot loader. This uses the `nrf_dfu_validation_boot_validate` function, which eventually calls into `nrf_crypto_backend_secp256r1_verify...
I use the above code to copy the device root key from the flash region. The if condition at the end results to FALSE always whcih implies that the key was not copied into...
Hi,
I would like to confirm whether bootloader should start from my application with BLE buttonless DFU. Once the request to enter the bootloader is received by my app I...
Hi,
I am running the Asset Tracker application from a fresh clone of the 0.4.0 nRF connect SDK. Using the supplied iBasis SIM.
It connects after booting, and I can monitor...
Hi,
Iam using nRF52840 , And got ANT sdk from thisisant.com. Placed in the required folder & Using ANTware II v4.1. All things going well, But after programming the DK nRF52840...
Hey Nordic Community ,
I have been trying to get the Modem firmware up and running without success for a few days now (Attempted with 2 different PCs and 2 DK with same...
hi....
i am using nrf52382 .. segger 15.2version
here i have attached two programs ble_uart and twi sensor ... its working fine but data is received over ble_uart app...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use CURVE25519.
I made my code refering to example "ble_app_multirole_lesc" and "nrf_crypto_keys.h".
NRF_CRYPTO_ECC_PRIVATE_KEY_CREATE...
Hi all,
When i walk-through the battery-service provided by nRF SDK, i note the presence of " Report Reference Descriptor " in the characteristic addition function.
I...
Hello,
I am trying to insert fds functionality to light switch client. I added all files and libraries to project. But when i try to compile project i face with errors...
When I am initializing BSD-library with bsd_init(), the function gives me back an value which i can´t find anywhere 0x00008108.
Hopefully you guys could tell me what this...
Are the virtual page sizes only allowed to be 1024 and 2048 for the nRF52840?
// This is a multiple of the physical page size. Is this allowed or not?
// <i> Expressed...
I am attempting to do the assert_tracker example. I have gotten all the code to build through Segger and upload to the DK. The problem is when I'm watching the terminal for...
Hello there,
I want to run Radio Test on one nR52832 based custom board.
I have flashed the example from SDK 15.3 on the custom board using PCA10040.
I have done the...
