Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
As per your sugesstion opened a new ticket in reference to existing ticket,
https://devzone.nordicsemi.com/f/nordic-q-a/60891/unable-to-read-the-128-bit-uuid-with...
Hi,
I'm using nrf52-pca10040 and sdk-15.3, I tested an eeprom chip following twi_scanner example, using no block nrf_drv_twi_xfer way, which works well, then I put it in...
Hello,
I followed this tutorial and github example in order to make a custom service with the characteristics I need. However, I am running into an issue where the board...
Hi.
I am using nRF52840 Dongle. A problem occurred while merging the PIN_CHANGE_INT examples based on the BLE_APP_BEACON example. I connected the external button to the...
In the products that I am developing we use advertising packets in the scan response to pass some data around our devices. We wanted a way for the app we've made for iOS to...
Hi,
I am using nRF52840, S140 7.0.1. I am using ble_app_blinky application.
I am writing data into FDS records. After writing FDS, if I load new hex file using nrfjprog...
Dear all,
I'm trying to go to SYSTEMOFF mode and then wake up from activity on UART rx pin (nrf51822).
If I do this:
nrf_uart_txrx_pins_set(NRF_UART0,NRF_UART_PSEL_DISCONNECTED...
Hello, I have a BLE peripheral, that should receive larger amounts of data using a l2cap channel. The central (a MacBook) creates the L2CAP channel, the channel is purely...
Hello,
we develop an open source framework that we are currently extending to also support the BLE Mesh Access Layer Models. We are currently implementing the foundation...
I am using nrf52810, using sdk15.2, softdevice6.1.0, my application flash takes up 56KB (I used fds), softdevice: 100KB and bootloader: 24KB, resulting in insufficient flash...
Hi,
I'm try to test my nRF52833DK using the nRF connect Direst Test Mode. Even if I flash the DTM binaries in nRF5 SDK 16, the Direct Test Mode app says something like ...
Dear Sir.
I am using SPI as follows.
gpio_pin_write(dev_io, LIS2DH12_CS_PIN, false); err = spi_transceive(spi_dev1, &spi_cfg1, &tx, &rx); gpio_pin_write(dev_io, LIS2DH12_CS_PIN...
The firmware is based on the BLE UART example running on an nRF52832 with the S132 softdevice. The first batch of boards were build with the QFABB0 chip revision of the nRF52832...
I have set up APP_BLE_CONN_CFG_TAG with
#define APP_BLE_CONN_CFG_TAG 1
Setting things up in ble_stack_init exacly the way it is done in the example, but when I run sd_ble_gap_connect...
Hi,
I am using nRF52840 S140 V7.0.1. I have few queries on GPIO configurations.
Below are my PULLUP/PULLDOWN macros.
As per my understanding
1) In below settings...
