Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hi,
I am doing a BLE based project using NRF51822. I am asked to build a 2 layer board.
According to the reference schematic BALF-NRF01D3 has been used with WLCSP package...
Hi,
I'm close to finishing the implementation of a system with a recording device with nrf51822, working with 6 sensors with nrf24L01.
The recorder is in receiving mode...
I'm looking for an approach to RF coexistence between an nRF51822 bluetooth SOC and a WiFi module such as the WL1801. Does anyone have any experience or recommendations for...
Hi guys,
I tried to flash the pca10001\blinky_example onto a nRF51822 with nRFgo Studio.
Flashing the s110 worked fine. But when I try to flash the hex from the example...
Hello All,
I'm thinking a small plastic case for a portable device.
It is possible to place pcb board (with pcb antenna) above the battery (Li-Po) or can interfere with...
I want to log basic intermittent events and push them to a previously associated mobile device when one is nearby. The mobile device can then forward the events up to a server...
I'd like to know what is the minimum and maximum frequency I can generate on a GPIO with a 50% duty cycle (+/-10% at the worst case). Which resources should I use for that...
In my case active CE signal defines byte boundaries - for each byte individually.
From what I see, DMA seems to stop on rising edge of CS regardless what is declared in...
Hello everyone,
I'm using nRF51822 development kit to do BLE network experiment.
The boards I use are PCA10005 with omnidirectional antenna, and PCA10004 with PCB antenna...
I'm looking at the UICR hardware peripheral example , and trying to figure out the utility in writing to the UICR registers.
Why would I want to modify the compiled hex...
Very new, so please forgive the questions, but...
I have an nrf8001 that I've powered up. After initial power up, I'm able to read the DeviceStartedEvent but the response...
I'm looking to integrate a digital (PDM/I2S) MEMS microphone into my nRF51822-based design. I'd like some pointers to reference designs or other information -- the ones that...
Hi,
I would to know why when the DC/DC is enabled the current is very high (57mA) during RF sending.
Why at the end of RF sending the current is higher than...
I am modifying the bootloader. I am not using DFU or any of that, but rather copying a FW image over from external flash through SPI. The area of my code that gives me problems...
