Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello
I am new to all of this and am wondering if this is possible, and if anyone can point me in the right direction if it is. I am looking to create an open source project...
Hi DevZone Team,
when I use west to configure a project, build/zephyr_settings.txt always contains
"BOARD_ROOT":"/home/user/test/nrf" "DTS_ROOT":"/home/user/test/nrf"...
I am facing one another problem basically i am sending some AT command from central to peripheral but after some time its hang and wait app_erroc. c (__disable_irq();->while...
Hello, I commissioned a factory to make a sample card reader for my company, they didn’t configure everything, because the SDK given to us allows the device to read-only NFC...
Hi
I have a setup with one device and one host, and I want to send data return to the device, but I'm not getting the nrf_gzll_host_rx_data_ready callback no the host. ...
HI
We have a running product that we want to improve by moving from ESB to Gazell.
it should be an easy task, because it is only a simple main file that needs to be replaced...
Hi Nordic,
I have added 20 client elements on a client node to control 20 server nodes(Light_Switch example). While sending an acknowledged message to all servers on a button...
We are using the nRF52840 with SDK 15.3 and we want to switch the regulators (DCDC or LDO) manually depending on the feature.
According to the Nordic document here ( https...
Hello,
I want to run a memory test whenever my device nrf52832 starts up to check for various faults like stuck at, transition and other faults in both flash and RAM. Does...
Hi All !
Hope doing well . I have a question regarding nrf52833 maximum power transfer @ 8dbm . I am using the "ble_beacon app" and using sdk 17.2.0 and soft device is S140...
Hi. I am working on the nrf9160. I want to use a unit test framework for my application code (which is a combination of C/C++14). I thought about using gtest/gmock or ztest...
I'm using NCS V1.5.0 and an nRF52840
The current draw with I2C enabled is around 200 micro amps
If I disable I2C using an overlay and recompile the current draw is around...
Hi all,
Please forgive the newbie question--I'm just getting started with Nordic.
I'm trying to build the hex files for the pc-ble-driver and the build keeps failing....
I am trying to add the nRF SDK 15.3.0 ILI9341 LCD driver code to my existing nRF52840 project.
Segger Embedded Studio 5.40a is being used as the IDE.
I have added all...
Hi,
I am new to Nordic chip sets, though I have firmware experience with STM and other boards. I have to wire an accelerometer to a nRF development board, and fix some existent...
