I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Dear Nordic Developers!
When I call the sd_power_system_off() function to put the MCU to system OFF, after that I can still see the advertiser device in MasterControlPanel...
Hi!
First of all, I'm using the nrf52 PCA 10040 DK, with SDK11.0.0, and my Soft Device is 132 2.0.2.
I'm developing an app for comunicating with a sensor via SPI (send...
Hi,
Am starting custom service to support custom profile and it works without any issues.
But when I add DFU service also to start after custom service DFU service fails...
Hi All,
I have a question about use of super/ultra-capacitor in a circuit using a module BLE (nrf51822 inside) instead of accu Li-Pol / Li-ion ?
it is possible to use...
I am looking to use the nRF51822 in my product and have been given a nRF51822 development kit however i have been looking for access to the Firmware and Hardware files and...
I have an nRF52 DK and have compiled (with gcc) and flashed an example that contains the line
NRF_LOG_PRINTF("SPI example\r\n");
I get the appropriate LED flashing...
Hi,
I'm trying to discovery the content of a vendor specific GATT service.
So far I'm receiving the BLE_DB_DISCOVERY_COMPLETE event and I'm able to see that I got 4 entries...
Hello,
I have a BLE Nano (nRF51822) and I want to develop an app which will find all BLE devices around (MAC addresses and RSSI) and send it by UART/SPI . I've used nRF...
Hi.
I'm using nRF51822AC, S130.
I made source code for RF test as below.
NRF_RADIO->SHORTS = 0;
NRF_RADIO->EVENTS_DISABLED = 0;
NRF_RADIO->TEST = 0;
NRF_RADIO->TASKS_DISABLE...
I tried MQTT subscriber example code, it compiles and loads successfully but it doesn't show the LED lights accordingly as I press the buttons, meaning that MQTT state is...
I am using S130, and I try to write an very simple program, when I push button_1 then it read ADC and print it our by UART.
So, write a "nrf_drv_adc_buffer_convert" code...
I connect to nrf51 DK board and PC using USB. I used RTT Viewer to see RTT log output.
But when I try to compile and download from keil to the board, I got several WARNING...
All,
Can anyone tell me what is the fastest time that a ble SD (5.x / 6.x) running on an nRF51 can (re)start advertising from a disconnect. Basically looking to do an ...
I am not able to connect Garmin Edge or SimulANT to nRF51-DK. Neither sensor nor receiver seems to work. Just looks like there is no RF.
Examples tried:
power_only_sensor...
