Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
hello,
i was trying to run the sample examples, i tried blinky example from C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001 folder. i was succesfull in getting the...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Dear nodic engineer:
i want test environment temperature with NRF51822 inner temperature module.
any information for reference?
any temp graph?
if need calibration?...
Hi,
I have an evaluation kit and I have custom boards that has nRF51822 chip on them.
I am trying to update the firmware(Application) of the custom boards from evaluation...
Hi,
I need to drive a piezo buzzer. Just need to make a simple beep function(s) that one call will start generating a specified frequency on specified pin and other call...
there is no sample code in nrf5188 sdk to use BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM,
what's the difference between the two settings?
for BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM...
Hi,
I am using IAR Workbench for ARM to develop my application and I'm experiencing a very frustrating issue with my debugger (J-Link that came with the development kit)...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
it happened that we have some hardware boards populated with older chips rev. QFAACA and some with newer rev. QFAAG0 but we need to share same software. As I read newer...
by set a char with BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS, means it can't be read and write, if so, why not remove the char?
any reason behind BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS...
Is there anyway to limit the number of channels a device is advertising on?
I'm using an nrf51822 with the S110 stack and want to limit my device to a single advertising...
