I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi,
I use vs code to run nRF9160 DK applications and it runs fine for a month. But recently I cannot build configuration even in an empty application . Old good applications...
Hello,
We have an nrf5340 custom board and during frequent BLE connections/disconnections sometimes it seems the netcore gets stuck. We are connecting to an iOS app and...
Hi:
Pls help me!
I use ncs v2.6.1.
C:\ncs\v2.6.1\zephyr\include\zephyr\sys\util_internal.h
When I check #define Z_IS_EMPTY_ (...) No matter what I input, I can't get...
Hello Nordic team and community,
I’m exploring the possibility of creating a mobile application (potentially using Flutter or native frameworks) that would act as a Distributor...
Hi,
I'm facing a critical issue with our sensor's power setup and would really appreciate any insights or suggestions.
Our sensor is currently using a CR2477 battery,...
Hi guys,
simple question based on your experience: what is a realistic data rate between an Android device and an nrf52805 with S112 on board?
I tried a lot of tweaks...
Hi, in our project we use the nRF52832 and a external flash memory MX25L3206E connected on this pins:
Take note in this project we also use SPIM0 to manage an IMU and...
Hi, I just purchased new PPK2 kit from mouser.
But after trying to open it via nrf Dekstop app it gives and error
2024-11-19T11:57:53.845Z INFO Selecting device with the...
Hello, I am trying to achieve a few uA current in nrf9160 but with even all conf off and empty while loop or even without the while loop the controller is consuming 5mA which...
We are currently working on a project based on nrf52840 and using connect sdk v17.0.0.
It is currently in development phase but eventually we are planning to use nrf5340...
Using v2.8.0-rc2 as v2.7.0 doesn't support the SCRATCH partition.
I am not able to enable BOOT_ECDSA_TINYCRYPT (required for Image Encryption).
I suspect this is because...
Hello
Awhile back I profiled my battery using power up app @ 4C 25C and 45C for a battery between 2.75V and 4.2V battery model is attached in zip.
The profiles themselves...
Dear Nordic Team,
I am working on a project using the nRF7002DK and require guidance on implementing the following functionality:
Acquire data from a sensor using the...
Hi, We have an application where we need to predict drift between two nRF52833 systems in low power mode running from LFRC (low frequency RC oscillator). Section 5.4.4.4 of...
