Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello. We need to add more end devices than default (10) on our Zigbee coordinator and that was solved with
zb_set_max_children( ZB_DEFAULT_MAX_CHILDREN );
where ZB_DEFAULT_MAX_CHILDREN...
Hi, I use nrfconnect SDK 3.1.1 and nRF52840 (as a dongle, DK etc) Using the power profiler kit 2 I see legacy advertising (TX/RX) peaks of about 32mA (with txpwr=8dBm, 3.2V...
Hi guys,
I'm working on this project which was basically a migration from STM32 to the nordic NRF52832 in order to enable the BLE beaconing mode.
It has been a challenge...
Dear Nordic Support,
I’m working with a Thingy:53 device and encountered a persistent issue during recovery. The device is recognized via J-Link (serial number: 1057760136...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
What is the permitted VDD ripple on the nRF9151?
I see " To minimize supply voltage ripple and suppress EMI coupling to and from nRF9151 VDD , keep supply network impedance...
Hardware Setup
Custom Board:
nRF52811 chip
No external LFXO (32.768 kHz crystal)
No LC filter for DC-DC regulator
No peripherals connected (no LEDs, buttons, sensors...
Hi,
I try to use the west ncs-sbom command to generate the result, however i meet below error happening but I had not idea how to solve it could someone help me to check...
The issue is that , i have custom board which have nrf52833 and nrf21540 (Range extender) , i have to increase the range of tx gain = 20dbm using gpio method
this is my...
Hello,
I have developed a bootloader with OTA update functionality on an nRF device. The partition switching code (bootloader jumping to the application after OTA) works...
I am running into a recurring issue with attempting to connect to a nRF52840DK advertising using extended advertising from iOS devices. Connections repeatedly fail to establish...
I am not using the nrf5340DK development board; instead, I am using the nrf5340 chip, and the SDK version I'm using is V3.1.0. I defined the I2C child node "lt3582" in the...
I set CONFIG_BT_DEVICE_NAME_DYNAMIC=y in prj.conf, and then called it after the system started.
These functions modify the Bluetooth name, but the new Bluetooth name has...
following on from https://devzone.nordicsemi.com/support/348883
I have code that executes and functions that return error_code = 0
but for peripheral mode the NRF conect...
