Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I have used an nRF 51 dongle for capturing BLE packets on my Mac using Wireshark,, but it no longer works. The only system change that I can recall that might affect this...
While working on some problems, I often find it useful to increment a counter at a line of code, and occasionally log the counter for developer debugging. I'd love to have...
Hello,
I decided to play around with an nRF24L01 chip and I'm trying to get it to work on my Windows 10 computer.
My current issue is the following: I've downloaded and...
Hi. I'm writing my own libraries for nRF52832 and I can't get UARTE to work.
Here is my code.
I'm using pins 6 and 8 as the UART example.
I wrote same code for UART...
I'm beginner with nrf chips.
I have a custom board with ntf52840 module. I connect board to stlink via swd interface, then check:
st-info --probe Found 1 stlink programmers...
I would like to perform observer role scanning i.e. passive scanning. I am using nRF52832, S132, SDK 15.2.0. I am trying as follows.
NRF_BLE_SCAN_DEF(m_scan);
static...
I am using the SDK5 development kit with Segger for a BLE application.
I found the Service for SES but the SDK doesn't seem to include the Pulse Oximeter service.
I would...
We are developing hardware to work as a AirMouse (Gyroscope based working mouse)
I am using SDK16.0 SES
I have seen that HID Mouse example
and i implement gyroscope...
I have bought a BLE Micro. ( www.seeedstudio.com/Seeed-Micro-BLE-Module-w-Cortex-M0-Based-nRF51822-SoC-p-1975.html) 1. I downloaded "nRF Connect App for Android" on the phone...
Hi there,
I've recently purchased an nRF52840DK with the 52840 SoC and I'm wanting to develop Bluetooth Mesh apps.
I'm on Mac OS X. Should I begin with the nRF52 SDK or...
Hi,
I just got the brand new Thingy:91 and would like to program it with an application earlier developed for the nrf9160 DK .
Further I'd like to use the Link Monitor...
Hi All,
Recently I have been working on nrf9160dk board. The use case is to have nrf9160 work as a serial LTE modem with GPS functionality. I have the following link https...
Hi,
I have implemented my own Vendor model, using the light switch client/server as a starting point. The model allows to send byte arrays. Since I have used the generic...
I am using SDK v16, SEGGER to program on my nrf52832 SOC for our project. I need to save a few variables to the flash memory. These variables will hold the status of the device...
Hello,
we are using SDK version 15.3 and mesh SDK version 3.2.0, on a nRF52840 DK board using the Segger Embedded Studio IDE version 4.52 (64-bit).
Our goal is to add...
