I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi there,
I'm trying to do a basic test with the GPIO/NMOS - just trying to turn an LED on and off for now. We're going to be doing this in response to the outcome of an...
Hello,
I'm working on the mqtt_simple sample in zephyr environment for NRF9160 board.
We tested the firmware with 2 sim cards with different packets: IPv4 and IPv6,...
azure_iot_hub_connect does the following check:
connect_client looks like this:
If the embedded return at line 40 of connect_client occurs (as I've seen it do) then...
I noticed on Zephyr docs this:
nRF5340 PDK (preview development kit) is an earlier version of the nRF5340 DK. nRF5340 PDK board is deprecated and is replaced by nRF5340...
Hi Nodic,
I try to add the tx power to both the connection mode and advertisement mode to make it long range available. But when I run the code it fails.
Please check...
Hi.
I do not find the description about I-Cache principles and work algorithm.
I read the part of the documentation "NVMC - Non-volatile memory controller". I think, I...
How can configure NRF_LOG_UART to use UART0 or UART1 for nRF52840? I cant see any configuration which uart NRF_LOG_BACKEND_UART will use
As per spec nRF52840 should have...
Hello,
I want to develop a new IOT product using the NRF52840. My device will be using the MCU with BLE and a very low power sensor.
I want to use a 3.7V one cell battery...
Hi,
I would like to input a data(integer) into the CLI and store the data. How can I do that. I have seen SDK but could not find any function or macro.
If there is any...
Hello, Not sure if this is exactly the same as what is happening in this case , but the issue of an early disconnect when NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, can simply be...
Hello
I would like to retrieve the signal strength of the Thread messages I receive. To do this, I used the otMessageGetRss (message) command in my request_handler but the...
I have cloned a few beacons with nRF Connect and use the app to advertise these when testing our beacons and apps. It is (to my best knowledge) not possible however, to export...
I have been trying to use the secure services to read random from the CC310 and have been getting unpredictable crashes. I have been able to modify the secure_services sample...
sdk ncs v1.3.
Example name: serial_lte_modem. Example path: D:\ncs\v1.3.0\nrf\applications\serial_lte_modem
The error in opening this sample macro definition is as follows...
Hello, Nordic developers. The ZED , ZR and ZC connections were identified by the example of Zigbee Light Control example .
Based on this example, we are going to develop...
