Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
I'm trying to work with the PC-BLE-Driver with the connectivity firmware. I've loaded the connectivty firmware and the application appears to connect to the board. But I'm...
Hi,
I working on the module developed based nRF52840.
I would like to clarify some doubts regarding the TX power of the chip.
The TX power value is higher at the temperatue...
I think there are should be smartphone cpu with bluetooth 5 long range mode support.
for example Qualcomm Snapdragon
Qualcomm Snapdragon 439
Qualcomm Snapdragon 710...
Hi all,
I am looking for some advice on how to implement a couple of extra characteristics(Related with battery) with the Battery Service apart from the usual Battery Level...
In " nRF51 Series Reference Manual ", in TWI chapter, it is mentioned to configure the GPIO pins with drive strength S0D1, to secure correct signal levels on the pins used...
In my application I'd like to use nRF52810 due different reasons. Since we're still in evaluating phase, without even choose a brand and related EVK, I've some basic questions...
Hi,
I am adding "install codes" function to my products.
Questions are
1. How many entries can i add with "zb_secur_ic_add" at ZC site?
2. Can i retrieve mac/ic (install...
Hi,
We are starting to measure the power of our nrf52840 based design.
I'd like to establish the power number for Idle() , since system will be in Idle() most of the time...
Hi,
I"m using SDK 15.3.0 with an NRF52840 dev board. I'm trying to record the timings from an incoming IR signal. In doing so I'm using LPCOMP with an analog input pin to...
I am trying to use the RF5 BLE CLI (Nordic NUS driver).
I need a plug and play COM port for Windows, iOS, and OS/X. This has to work for a customer.
It pairs easily, but...
My team is in the process of developing a product that uses the Fanstel BC832 module and have been running into issues trying to implement buttlonless DFU in our application...
I'm developing a fingerprint-related project. When the finger touches, the fingerprint sensor generates a pulse signal. NRF52810 will triggers a GPIOTE callback, then wakeup...
I try to bonding func using ble_app_gls example.
just connect is fine.
here is ble_evt handler
for trying connect bonding, I use pm_handler_secure_on_connection(p_ble_evt...
Hello,
I would like to use the nRF52840 for a wearable. It should be powered by a lipo-battery with 3.7V. Therefore I would solder it to the VDDH and Ground Pin (VSS). Is...
Hello .
I try to connect my JLink to my nrf51422QFAA cunstom board. And I use J-Flash to test ifg it can readback and it is OK. But When I try to use nrfjprog, I got some...
