I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
We have been manufacturing for a while with the nRF51822, Revision 2, and WLCSP package and build code D0 (D0 is what Nordic recommended me to spec to contract manufacturers...
Hi all,
I have application that read analog level and send the data with connection interval of 10 ms and 0 dBm, how can i calculate the current consumption of BLE? i read...
Hi
I want to use Printf() in the DT2 but it cannot output msg to terminal.
I used hal_uart_config() to config UART TX/RX/Baudrate... in mail.c then
call hal_uart_put_str...
I use S110 V7.1.0,nrf51822 chip,
now I need write and read flash data in BLE mode.
When can I write the flash data at BLE mode?
When can I read the flash data at BLE...
I'm calling the requestData function and lib_aci_close_remote_pipe at the same time.
The lib_aci_close_remote_pipe returns 0x8E command error which means: "Command rejected...
Hello,
I need to store some app configuration on the FLASH and I'd like to use the features of pstorage module.
I don't understand the following thing ...
When the...
Hello,
I am currently using the SDK setup from this URL: embeddedsoftdev.blogspot.de/.../ehal-nrf51.html
In order to use that setup, one must change a line in the file...
Hello,
I downloaded MDK arm from Keil website (keil mvision 5), SDK and MDK pack from nordic download site. After installing SDK, I am not able to find example projects...
Hello,
I have quite a few of setting on my nodes and I want to save some of these permanently. Currently I am using the pstorage module and everything works as expected...
Hello everyone,
i can able to set the static passkey but i would like to know the difference bewteen security key and passkey how can i set security key ? any suggestions...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
I am trying to communicate with a SPI peripheral, using the nRF52 as the master, and the peripheral as the slave. What happens is that it still faults out, and the presence...
