I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hi, we are still struggling with nrf9161 behavior and trying to mitigate data sending dropouts ( and ).
Here is one partial issue: we are currently using UDP and flushing...
using west update i just update the old version 3.0.2 to 3.1.1 and after take blinky code and build then i have got below error,also using the vs code i doenload the NCS v3...
Hello, While designing the hardware circuit for the CAAA WLCSP with internal LDO regulator setup on the nrf52810, I removed the 32.768kHz crystal oscillator and retained only...
I am currently developing my project using the nrf52832 and the nrf5SDK.
I utilized the peer_manager module, and in the application, when being connected as a peripheral...
Hi,
I’m using an nRF5340DK with nRF Connect SDK 2.9.1 , configured as both Central and Peripheral with the nordic SDC running the network processor Goal: allow the board...
The High-Performance Framework (HPF) is a framework designed to support the development and integration of software peripherals using coprocessors (e.g. FLPR on RF54L15)....
Hi,
I managed to get Channel Sounding with Pixel 10 as Initiator working, based on this change on mainline.
https://github.com/nrfconnect/sdk-nrf/commit/30f67fc0b6be8051b5d8f73d900675dd98758631#diff...
Hello Nordic team,
I'm developing a BLE peripheral using nRF52833 and would like to validate that my approach for handling connection parameters aligns with Nordic's best...
I now need to make a program on nrf5340 audio DK, SDK v3.0.2 to scan extended adv and print the BASE information in the subgroup in PA, without sink BIS, besides, a smartphone...
Hi,
I am following the course "nRF Connect SDK Fundamentals" and am almost at a standstill when it comes to progress.
I am still struggling with lesson 1 and lesson 2...
Freshly installed VS Code natively on Windows (also tried on Linux and WSL with same result) with NRF Connect Extension Pack, SDK 3.1.1, Toolchain 3.1.1 was used to create...
i get various answer about this, been in the rf design for a while, we used to make global antenna lenght on some give am ook circuit a tad shorter and then use a load cap...
Hi Nordic
I am working with nrf52840 and nrf52832 using ncs v2.8.0
I am trying to save coredump to flash according to instructions on this link - https://docs.nordicsemi...
Hi everyone,
I'm working with the nRF52840 using the nRF5 SDK v17.1.0 and SoftDevice S140 v7.2.0 . My application uses QSPI for external Flash communication.
I have some...
Hi,
i just noticed that for the nRF5340DK board, the file nrf5340_cpunet_reset.c has been removed.
Nevetheless it is still reference in the documentation online: https...
