hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I have run the example in ncs 3.1.0 for CS_RAS_Initiator and compared to the older version ncs 3.0.1, there is a new flag called realtime_rd . Thanks to this, I can...
Hi,
I have a question about Channel Sounding: I want to run the CS procedure with 4antenna paths. Both the reflector and the initiator have 2 antennas. I started with the...
Hello!
I know IDAP-Link is not a product from Nordic, so maybe this is not the place to ask this, but...
I have to develop firmware for a custom board based nRF52 that...
I was able to compile and run the Hardware ID example on the nRF5340DK & SDK v3.1.1 using VS Code successfilly, but as soon as I add the overlay-ble-ma c config it still compiles...
This is the first time I've used two roles on one device and I've encountered some oddities.
The topology is as follows: Device A (nRF52840-DK) operates in dual mode (but...
Hi,
I was at the webinar today where they talked about SDK 3.0.0. They mentioned that the QSPI examples were "JESD216 flash" and "JEDEC SPI-NOR flash". I don't see either...
To preface:
Board: nRF9151 custom board nRF Connect SDK / Toolchain: 3.1.0
Hello,
We just received our first article boards for a design that uses a nRF9151 module....
Hello,
After completing DFU on the nRF5340 DK, the default behavior is to reset the MCU. However, instead of performing a full reset, we would like to jump directly to the...
Hi team , I have developed the code where i am able to do OTA in dual slot when my application size is less , but my current application size is aprx. 260 KB and i want top...
When we were using nrfjprog to flash, we used "west flash --erase" because it was quicker to erase entire flash then sector by sector. However, when we upgraded to SDK 3.0...
Hello,
I have a custom board with nRF9151 and nano SIM card. I have flashed at_client sample to the module and trying to test different at commands.
It seems only PTI...
We are using the Nordic Semiconductor nRF7002-DK . In this board, both PS-Poll and No-PS-Poll power-saving modes are working as expected. However, when running in TWT (Target...
Hi,
I want to report a bug/issue with the NCS, is this the right place to do that?
We are compiling for C++, so when including headers like <net/nrf_cloud_coap.h...
The meaning of IQ data in the channel sounding example I am trying to use IQ data to calculate distance using the routines ` channel_sounding_ras_initiator ` and ` channel_sounding_ras_reflector...
