Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi
I'm using SKD16.0.0 and S132, and I want to realize that peripherals can only connect to a center with a known MAC address through directed advertising. How should I...
Hi Folks,
I am getting in trouble with SoftDevice activation. Indeed, my application did not return from the "nrf_sdh_enable_request()" call, more precisely it hangs into...
Hello,
I am currently working on BT840 and BT832 modules and trying to run the sample codes which are given by Nordic (specifically ble_app_uart which runs with UART service...
Hi,
there is a number of tickets on the sd_ble_gatts_characteristic_add, but I still can't get where I do it wrong :-(
I'm trying to initialize the battery service using...
Hi,
I used 52840DK and SDK15.2 to test usb cdc, every thing goes will, but in rx event, it always missed first byte, for example, if send "123456", it just received "23456...
Hi everyonoe,
I would like to set a timeout for advertising, and catch this event. So I have
According to ble_gap.h :
uint16_t duration; /**< Advertising duration...
Hello,
Help me please, I have an issue with ATT MTU size.
When connecting Android (BLE client) to nrf52 (server) and ATT MTU is 20 bytes in max.
I have changed on...
I'm using SDK v16 on an nRF52832 and occasionally run into a SIGTRAP with my custom application mainly forwarding BLE traffic from/to UART.
It works fine, only after quite...
Hi teams,
I am finding a way to check whether a mesh node is currently able to communicate with other node.
We are planning to deploy many mesh nodes to proper position...
Hello! We are using the chip nRF52832 with the circuit recommended by Nordic Semiconductors, we want to implement the recharge of a battery by NFC. Without any data transmission...
Hi, I am trying to put nRF52832 in low power. My starting point is NCS v1.2.0 peripherial_uart app. When started I had ~300uA in idle mode, and that was because UART was always...
I've been trying to transfer a DFU update via serial, and I have gotten error 135 each time.
A colleague of mine got it working this january, with v3.1.0. Now, the same...
Hi,
1 - I don't understand why on the PCB layout example the track that is connected the L2 inductor is 762µm thick while the thickness of the pcb is 0.8mm?
2 - To have...
Hi,
We would like to know whether below programmers can be used to flash both NRF9160 application image and modem image. Also whether any command line support is there....
I'm using SDK 15.2 I'm trying to read two separate events configure in two separate pins ( PIN_1 and PIN_2 ) with two different handlers ( handler_1 and handler_2 ), like...
