Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
Hi,
I want to test eddystone example with nRF52833.
The default project doesn't include PCA10100.
I am trying to create one, but it always stuck in the function nrf_crypto_rng_backend_init...
I believe from reading some of the existing posts that my JLink EDU mini programmer (with SWD connection) should work with the nRF51822 (it shows up as a device option in...
Hi,
I want to build a bluetooth central example of zepher to nrf52832.
I am using the command "west build -p auto -b nrf52832_mdk samples\bluetooth\central" to build the...
I'm using 51822 QFAC, SDK11 S130 2.0.0.
I'm able to write to flash using fstorage_write() below. But the problem is whenever I put a for loop after I call fstorage_write...
Hi,
I built a simple custom board with an nRF52832 ebyte BLE module with no added components except for the RST and DFU buttons, the serial wiring are the same pins (RX...
Hi,
I'm working on a BLE scanner which need collect data from the beacon's scan response packet.
As far as I test, the current mesh beaconing example cannot get the scan...
I plan to use nrf52840 in high voltage mode (connected directly to the power source via VDDH pin) with button.
And I plan to use voltage regulator with EN pin (with pull...
The most relevant thread on this topic is two years old. I do not want to use Keil as it is so costly and the project may not go anywhere. I am not interesting in using the...
Is it possible for me to easily modify the nrf52 Zigbee samples to run on 1 or more of my 5340 M33 cores, or is it a rewrite?
I can see chip support for nrf52 but no mention...
Hello,
We recently sent a design to our board assembly house for review and they indicated that the large copper area under the nRF528323-CIAA (WLCSP) may result in head...
I’m using nRF52810 on a custom board (for our own application) using SDK 15.2.0 v6.1.0 S112. Given the amount of memory this chip has (192/24 KB) is it possible to implement...
I'm using the nRF52 DevKit with nrf52832 SoC. I connected a UV Sensor through the TWI interface (PINS 26 & 27, as well VDD and GND).
However, I fear it's using a lot of...
Hello,
Till now I was using nRF52840 with nRF5_SDK_16.0.0_98a08e2 and its working fine. Now I thought to cross check with nRF52832.
When I run FDS example I am getting...
I have been studying the power consumption of a prototype and observe that the end device is polling very frequently. The data request polling is backing off for a while to...
