How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi all, I've just started moving to the nrf52840 platform from another ble module. I'm taking samples from a bunch of sensors at about 20 hz, since this is a battery powered...
Hi Dev Team,
I am using the mqtt_simple example to publish my data out every 1 hour. I tried the example and it is working well and I was able to test it via MQTT.fx with...
Hi,
Is it somehow possible to plot data comming from external target board with nRF52, connected to nRF52 DK via swdio and swclk lines, by some data plotting program? Etc...
I am using NRF52832 for BLE application with softdevice 132 under SDK15.3. My application is supposed to sleep off after certain amount of time when there is no user activity...
I am using two SAADC channel on nRF52 DK, one for pressure sensor and another for battery level. I realized 0.5mA is higher than single channel. Is it normal?
We need to develop a portable device，In order to save cost and low power consumption.We need to know how to make nrf52832 connect to the Internet through the Bluetooth network...
I wrote a program to toggle the pins of P0 and P1.
When I write:
P0=0xff;
P1=0x00;
Only P0.0 - P0.3 are high and P0.4 - P0.7 and P1.0 - P1.6 are low.
P0=0x00;
...
Hello,
I am talking about nRF5_SDK_17.0.2_d674dde/components/libraries/log/src/nrf_log_frontend.c.
In the case of HEXDUMP there seems to be some inconsistency in the packet...
Just downloaded this (5.10d) on MacOS 10.15.7.
(Planning to test with 9160 DK.)
Using getting started assistant
Got as far as the "setup a project in SES" (installed...
This is our 4th nRF52840 DK this year that got damaged this way. After using it for 1 to 2 months the DK does not work power up normally. Then we can only use the board with...
In RADIO - 2.4 GHz radio TXPOWER register say:
"When the radio is operated on 1.2V, the output power is increased by 3 dBm, i.e. if the value -20 is specified, the output...
Hi,
We are having some EMI issues with USB full speed and would like to force the nRF52840 USB controller to operate in USB low speed mode. Is it possible to configure the...
Hi
I use the following script to program my boards which takes 20 to 30 seconds to complete. But recovery and programming done through SES for the same code is much faster...
