I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hi,
I’m currently trying to design my own pcb based on nRF52 Development Board. I went through a number of pcb files and all of them are associated withnrf52832 without...
i use the keyboard project, bond and pair the iphone7(ios11.2), the iphone display is connected,ok, then i reset the keyboard and erase bonds, the iphone display disconnected...
Hi Dev Zone,
I am attempting to flash a blink led app, based on Zephyr (nrf52_pca10040), to the primo core (contains Nrf52832), through Jlink debugger on a Linux machine...
At what voltage should DCDC be manually turned off for a nRF52832 ?
This thread for nRF51 says:
You must manually disable the DCDC when supply voltage goes below...
Hello,
I followed the steps mentionned in this blog
I did all the required step but I'm still seeing the same behavior.
below is my setup :
I'm using nRF52840 and...
Hi folks,
We got a weird behaviour with our nrf51822(SDK 12.2.0, s130) device. we have built a low power application with following parameters:
MIN_CONN_INTERVAL...
I have tried to understand how data was send from two BLE device. I have had 2 PCA10056 board and I have loaded ble_app_blinky example and ble_app_blinky_c example for each...
Hi All.
I have one question.
I just want to send "volume down key" simplely after connect with android device to take a picture.
I have no idea. and I don't understand...
I modify nrf51 nus in SDK12.3.0 to realize my application, I found when enable uart, the consumption near 830uA , and then call app_uart_close(), the consumption near 5uA;...
Hi,
Is there and C/C++ source code to get float value from 32-bit ieee-11073 FLOAT data type
I need c/c++ code to parse 32-bit ieee-11073 FLOAT data coming from FORA...
Hello,
Using Spi bus with frequency = 4Mbps give me this deformed signals (clock and miso) and when I push it to 8 Mbps I am not able to get the correct values.
Obviously...
When an event is bound to the ppi channel, and this channel is bound to both task_capture and task_clear
can I get the correct COUNT value when an event occurs?
Or can...
Hi all,
I wanna build a IOT gateway. I follow this steps infocenter.nordicsemi.com/index.jsp
When I access coap://[ipv6] It dont have resource light, just only have...
[SDK 12.3.0 / nrf52 DK / Keil tool / beacon example code]
Hello. i am a novice developer.
Power On - Beacon data transmit and enter to sleep mode after 10 sec
...
I fail to integrate “ble_app_multilink_central” and the uart portion of “ble_app_uart_c”
I have checked other posts and it is inconclusive if and how they got the integration...
