Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hello.
I'm working on disconnecting ble from the module.
I'm using the app provided by nordic.
I designed it to disconnect the ble when I press the button on the module...
hi.,
we develop a product that use nrf52840,and it need to suport usb dfu in windowns and mac.and also need achieve cdc communication .this funcation is ok in windows,and...
USED SDK: v1.4.99-dev1
USED BOARD: nRF9160DK
Received hexvalues above 0x7F (decimal = 127) are counted double in p->message.payload.len Any ideas what might be te problem...
We are trying to evaluate the BLE Mesh for a product range and are evaluating the nRF52832 for the same.
Working with the nRF Mesh SDK, I am facing some issues, which are...
Under the recommended operating conditions (page 611) in the nRF52840 datasheet, there is a note specifying:
Given a device (with SWD access), is there any way to detect...
Hello Sr,
Take a look below Error, when I run the demo code from
C:\..\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\multiprotocol\ble_thread\ble_thread_dyn_mtd_coap_cli...
Hi,
We have created an application with BLE multi peripheral where I have to put my chip into deep sleep mode by long pressing the tactile button & also I have to wake it...
In the nRF51822, there was a bootloder area, but in the nRF52810, there is no area except for Application, and the image is as shown in the map below, is that correct? --...
Situation: SES, SDK 16, nRF52832, no BLE.
I'm trying to use both the UART and TWI 0. TWI works fine with BLE and all the rest. However, when I enable the UART, TWI quits...
Our device has been in use for a year using the nRF52840. We elected to not load the 32KHz crystal on our board. Everything seems to work OK and we have no BTLE issues, however...
Hi,
I'm using nRF PWM Driver and I didn't find the way, how to invert logic of PWM. I would like to reach this behaviour:
If I set seq_value=0, I want to have
PWM...
Hello,
We are currently using the NRF52840 with SDK 17.0.2 with S113 softDevice. We have our own boot-loader implementation. Is it possible (advisable) to perform an Over...
