Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
Hello,
In nRF52832 we use these commands to write data to user information configuration register:
nrfjprog -f nrf52 --memwr 0x10001080 --val 0x00010000
and use memcpy...
I had my environment running fine with (IIRC) SDK 1.4.x and Segger J-Link v688. I thought "it might help" to upgrade to the latest SDK.
I have the new SDK built and apparently...
Hello Use the S132 Central. Use two S112 peripherals. I want to communicate data to two connected peripheral devices at the same time. You are using nus. The connection was...
Hello,
I am working on a wearable device and need the lowest power consumption possible. The project configuration is:
S132 7.2.0
SDK 17.0.2
The board is powered...
Hi There
My design is basic on nrf52840. I need a pin be controlled alternately by GPIO module and PWM module in my application. The PWM function is realized by setting...
Hello!
I am now working on a customer board based on NINA-B3 module (NRF52840).
I found a weird problem: after successfully flashing firmware through SWD for several...
I was working in a Zephyr project and wanted to test something on my nRF52840-Preview-DK board - which I had just used minutes before and successfully had `west flash` write...
I'm trying to compile the serial LTE modem to trial the functionality.
The version as set by the import examples program in SES does not compile:
The error: mkdir(modules...
I set up PPI so that it kicks off TWIM (I2C) transfer on GPIOTE pin transition low to high. Everything works great, except that I also setup a fork task to set another GPIOTE...
Having a BUS FAULT while trying to use uart_tx on the NRF5340 with NRFConnect SDK. Based on the peripheral_uart sample project. Any ideas what may be causing it?
Heres...
This took me a while to figure out.
The default values for the WDT configuration in SDK 15.3.0 (and 16.0.0) is spelled as "NRFX_WDT_DEAFULT_CONFIG" ?
RMV
The following code has an unexpected out-of-bounds array access:
Primary cause is this line:
On an uninitalized pin number, channel_port_get() returns -1, which...
Firstly my current usecase:
We are using a STM32 as a main processor. the STM uses UART to communicate with the nRF52 using the serialization stuff. I currently have most...
Using ncs v1.4.0, modem FW v1.2.3, SES v5.10d.
I'm trying to get NVS working using /zephyr/samples/subsys/nvs. It is failing to write. I also tried the code in this post...
hi
i was trying to interface sd card with nrf9160 in segger emstudio. i was following the ticket Reading SD card on nRF9160dk - Nordic Q&A - Nordic DevZone - Nordic DevZone...
