Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello, developers! I am wondering if the Light switch demo and the thingy52-mesh-provisioning-demo serve the same purpose. I tried to run them combined: the first one on an...
Hi,
I'm completely new in the nordic development area and I'm trying to read sensor data from a DHT22 Temperature and Humidity sensor.
I'm used to directly include libraries...
Hello:
I am working on a USB bootloader project. I am running into the issue where the USB will not boot on first start up but boots following this. I read some of the previous...
It appears that there is a bug in the antfs.c sample code in version 15.3.0
nRF5_SDK_15.3.0_59ac345\components\ant\ant_fs\antfs.c
It the transport_layer_cmd_decode(...
I have a custom board using nrf 52382 with NFC. While Developing application I have checked nRF52832 Revision 2 Errata .
I have a question related [218] NFCT: Frame Delay...
Hello,
Our application runs over nRF52840 + SDK16 + FreeRTOS and we are using libuarte application to drive the UART. We found that the app_timer_freertos.c doesn't provide...
Hello ,
When i am using sdk functions with freertos some of the callbacks/functions requires (for example) xTaskNotifyFromISR() instead of xTaskNotify .
So how can i decide...
I am going to mass-produce beacons with built-in ble uart app sample.
However, I am not sure those produced beacons will have unique mac-address.
In my view, those are...
Hi all i am trying make a communication between esp32 and nrf52840 using UART. Initializing the uart driver was proper and pins also correct. when nrf start transmits then...
Using nrf52810 SDK 17 ble_app_hrs for my example, and i add some code about the passkey
Now the situation is after I enter the passkey on my Iphone nRFconnect app, and if...
As with my recent inquiry about a softdevice assert at PC=0x24e70 , I'd like to know which assertion fails in softdevice S132 version 7.0.1 at PC=0x157ec.
Is there a table...
Hello,
I observed a weird behavior when I changed to nRF52840-DK from nRF52840 Dongle. I am using the device as an SPI slave connected to a Raspberry PI as SPI master. ...
While trying to execute the light switch example, i was able to set the nrf52840 as evaluation board as proxy server but failed to do the same with the dongle.
2)When...
Hi,
When running the at_client example, I send the AT+CFUN=1 command via the LTE link monitor. After a few seconds, the nrf9160 reboots.
I want to say that before my program...
Hi all,
Currently I am working on my first project with the nrf52832. All is going quite well, but I would really like some help with my flash layout, basically I got some...
