Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I'm trying to connect to my local LTE network but I can't pass the yellow and blinking LTE step. I couldn't also run the Asset Tracker project. Please tell me if you are covering...
Im trying to connect Thingy:91 and Thingy:52 to my mac book pro using USB cable to use AT config commnads. In both cases I'm getthing the following messages in the log window...
Hello there!
I was trying to look up some default values to take an RF measurement and I was wondering what the default Tx power is for the Advertising portion of the app...
I've finally worked around some funky bugs that only appeared after updating to 15.3. In my app, I had to change my clock source to RC or SYNTH to make it work (was hanging...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Ok so I am trying to integrate SPI master and slave initialization code. I am very confused about legacy and non-legacy drivers and HAL. I am getting strange compilation and...
Hi,
i am working with nRF52832, i need to us sleep.it may be do somthing and sleep 40ms,rtc wake up it and do somthing and cycle.
i see the rtc example but it may be some...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I called "pm_init" to do "PeerManager". Then, a part of FLASH has been written to "DE C0 AD DE FE...
HI,
I compiled MQTT sample, and always got :
ERROR: mqtt_connect -60
timeout error.
It seems that it takes about 2 minutes to get LTE link connected:
LTE Link Connected...
https://github.com/takafuminaka/nRF52832/blob/master/i2s_ws2812b_demostration_planB/i2s_ws2812b_drive/i2s_ws2812b_drive.c
I read the documentation, but didn't really grasp...
I'm attempting to use the UDP with PSM sample provided at this Nordic nrf9160 samples branch . I haven't changed anything within the sample itself. I've been using it to demonstrate...
Installed Segger Studio v4.12, nRF5 SDK(latest version), J-link, all under same catalog but into their own respective catalogs.
First, if I open blinky catalog and choose...
I am receiving "ERROR 4097 [Unknown error code]" returned upon calling nrf_sdh_enable_request. I found that ERROR 4097 corresponds to NRF_ERROR_SVC_HANDLER_MISSING from some...
I have the following code. I need to add a second counter attached to the spi_end_event. The first counter "count_task" is working, but can you tell me how to get "count_task2...
