I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
Hi,
I use the calendar to display on the screen the actual date. It works but now I want to display it only when I press a button, but the button doesn't work. When I press...
Hello everyone,
I'm using the nrf52840 Dev Kit (PCA10056 1.1.0 2019.19 683465548)
SDK version: 15.3
OS: Fedora
I work on a custom board and try to put it in SYSTEM...
Hi,
We are using nRF51822 chip, and we are using TL3315 switches. I am very new to dealing with buttons. The current problem is that when I press the button, the MCU seems...
Hi,
I would like to flash a CC3100MOD wifi chip from TI with the Nordic 52832 chip as a host. Attached is my schematic. I am fairly new to the nordic family but I have...
Hi,
The problem statement mentioned below.
What we are trying to do is Read Light value from the MAX44009 sensor on the TWI interface.
Looking at the data sheet for...
Hi,
I am using Nordic nRF52840 SoC with nRF5_SDK_15.2.0_9412b96 (SDK) and S140 softdevice. I tried to set Tx power to +8dbm using
rc = sd_ble_gap_tx_power_set (BLE_GAP_TX_POWER_ROLE_ADV...
I am currently involved in developing a product that is using the nrf52840. The product needs to keep precise time across a wide range of temperatures, which is why a 32Mhz...
Hi,
When I try spi commnucation with sensor on nrf52840 (using Mbed OS with SDK14.2), it stuck to nrf_spim_task_trigger (p_spim, NRF_SPIM_TASK_START); while spim_xfer is...
Hi,
I am trying to increase the sampling rate of the motion sensor on a Thingy:52. I managed to update the firmware and increase the BLE_GAP_ADV_INTERVAL_MAX from 200 to...
I am using softdevice s132, nRF52832 and SDK 15.3
This happens every time I connect the RX line.
This is an application where I implement UART with the HRS application...
Hi,
I am interested to know how to make a mesh node (for example, a light server) compatible to perform a DFU.
I have gone through the DFU page and I noticed that the...
Hello.
I am about to receive the Uart service for the Nordic SDK Central and peripheral.
I Use nrf 52832.
In the peripheral example, we used 'ble_nus_data_send'...
Hi,
I am using nRF52840 Enineering C chip on a custom board using SDK v15.3.0 with SoftDevice v6.1.1
I have modified the Blinky Central code and the Blinky Peripheral...
Hi. After my nRF52832 peripheral connects to an android / iOS, I am trying to read the MTU size that has been negotiated with the following code;
current_mtu is being...
