How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
It looks to me like ANT_STACK_CONFIG is redundant in SDK 14.0.
nrf_sdh_ant_enable does all the same setup plus, it looks after all the new softdevice handler stuff.
...
Hi,
When I use nrfutil to generate a zip package, there would be three document in the package. Is there anyone know what does .dat and .json document use for? Could I...
Hi there,
I am begineer for nrf51822 and I want to interface MPU6050 WITH nrf51822 so can somebody provide me the tutorial with full detail.i want to read just raw values...
Have been following the nordic tutorial to update characteristic value using hvx_params. Currently the structure for hvx_params is as follows:
/**@brief GATT HVx parameters...
Hello every!
I am working with ATT_MTU_Thoughtput example (S132). My purpose is send data from "sever" to "client" and wait until "client" response to confirm . I was send...
I’m debugging the ble_app_blinky demo on a nRF52840-Preview-DK board (BOARD_PCA10056, S140). The device name in the debug configuration is nrf52832_xxaa.
Each time a breakpoint...
Hi all,
i use a nrf52 and in product specification i find the table about the low power mode and their consumption . Capter 17.1.
ION_RAMOFF_EVENT System ON, No RAM...
Hi all,
I have been playing with my PCA10040 and I came across the problem. I thought that it was a softdevice problem, so I went to bootloader mode (by connecting with...
Hi,
would it be possible to have multiple GAP Addresses for one nRF device? I was able to have this with the S130/S132 using verison 2.0.1 by using gap_address_set and...
Hi,
I have nRF52840 dev board which was detected and LEDs were coming on.
I tried programming the prebuilt throughput hex file in nRFgo Studio.
C:\Projects\NORDIC\nRF5_SDK_14...
Hello dear sir/madam, i have just started with BLE using nRF52832 DK .but i am not able to understand the examples.and don't know how to make any change.what is the basic...
My nRF5x DK kit has suddenly stopped working and I experience one or more of the following symptoms:
My kit doesn't show up in my computer.
LED 5 on my kit doesn...
Hi,
I have a ble scanner working well and i am trying to trigger start a compare timer within a timeslot.
starting the timer in the timeslot with the below code makes...
How does scanstart serial command work in the Mesh SDK?
According to the documentation, it appears that the command lists out unprovisioned beacons. I get a success response...
