In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
The SAADC on the nRF52832 consistently reads 20-30mV low, regardless of the source (AIN channel or VCC), Tacq, Resolution, or gain. All of the measurements are using the internal...
HEllo,
I am trying to set up a whitelist advertising and scanning, and while the advertising seems to go fine, I am getting an APP_ERROR:ERROR:Fatal on my central while...
Hello all,
Accordingly with nrf52832 product especitifation when radio Rx is active there's a additional 5.4mA consumption. My doubt is how softdevice s132 handles the Rx...
hi!
i am working with the nrf52 and i am looking for a timed sleep mode, meaning, a function that goes into sleep mode for a given duration.
is there anything like that...
Hi all,
I am working on my Central device to request pairing to my peripheral ( I asked about the peripheral in my previous post , both are running a nRF52DK and SDK13...
We have shifted our development from nrf51422 QFAC (32kB RAM and 256 kB Flash) to nrf51822 QFAA (16kB RAM and 256 kB Flash).
I'm unable to run dual bank ble bootloader...
Hello,
I would like to signalize that the DFU process is running. I mean when I start to upload the application into the CPU, then a LED (for example) is ON, after uploading...
We have been successfully using the Softdevice s132 to communicate with a smartphone using BLE. However, we have run into an issue with the compliance testing in the new requirement...
Hi All,
I am a beginner in app development. I am working on a project where i am supposed to transfer texts to my pca10040. Although i wanted know if i can modify nRF Toolbox...
I'm taking a look at the timeslot API example here , which was linked to in the answer to this question .
Very interesting! As I gather from the documentation for S110...
Hi,
I would like to have accurate (1-5ms), synchronized timestamps for logging events from a set of nRF5x boards, spaced tens of meters apart. Each nRF5x board is connected...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
I am struggling to find a starting point to be able to program the beacons. I'm completely new to this but want to be able to change the tx power so that they are only visible...
In my application, a static passkey is given to the user(I have implemented static pass key in my application and it is working).
Suppose the Nordic device is advertising...
In "ble_app_hrs_freertos" project, I try to change NRF_SDH_BLE_GAP_EVENT_LENGTH to 320 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE to 247.
And when I try to connect to the nrf52832...
