Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
I tried to set a custom key in this way:
... ANT INIT
uint8_t network_number = 2;
uint8_t p_network_key[8] = {0xa1, 0x15, 0xb3, 0x66, 0x60, 0xef, 0x19, 0xa1};
err_code...
Hi there.
I'm woking with sensor in board nRF51822.
Do we have any tool to test oscilloscope i2c?
I want to check the signal is same as what I sent or not.
Thanks...
Since nRF51 is multi-protocol, why don't Nordic provide support for Zigbee? This way, customers can simply buy one single chip and have several standards supported. Are there...
I received a NRF_ERROR_INTERNAL error from a pstorage_store() function. As far as I can tell this error should not result from this function. It occurs fairly randomly. This...
In the examples delivered by Nordic, there is ble_app_hrs in ble_peripheral and ble_app_hrs_c in ble_central. But I cannot find a ble_app_hts_c in ble_central for the ble_perifpheral...
I am using Master Control Panel to check some off the shelf BLE product. I noticed that some of them don't provide characteristic value when I press "discover services". ...
I am using the "nRFgo SDK 2.3.0.10040".
The datasheet of 24LU1P says the size of the bootloader is 2K.
But when I build it in Keil, the build information is "Program...
Hello.
I am using a nrf51822 with sdk 10 and softdevice 130.
It has an accelerometer mma8653 to read the orientation of the chip, I am trying to get the x,y and z co-ordinates...
Hi there!
I have nRF51 DK (PCA10028).
I config GIPO as below:
nrf_drv_gpiote_out_config_t out_config = GPIOTE_CONFIG_OUT_SIMPLE(false);
err_code = nrf_drv_gpiote_out_init...
Hi, I am generating PWM waves using GPIOTE, PPI and Timer. (I cannot use the app_pwm library from SDK 10.0 because there is an intial delay of ~600usec for the PWM to get...
Hi,
I want to generate PWM pulses of width 14uSec(off time) and 42uSec(on time). Is it possible to achieve the above
with app_timer module
without app_timer module...
