Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
So I've been having issues with my debuggers where occasionally Keil will crash and I won't be able to reconnect to the debugger interface without a power cycle (might be...
Hi, My project is that when a button is pressed on a slave (nrf51822ek), a central (another nrf51822) gets to know which slave has triggered and sends its status 1/0 to a...
Hello,
I am using ISP130301-Development Kit 1 for nRF51822 from insightsip.com which consists of postimg.org/.../
There is used a button on PCA10028 for deleting bonds...
Hello, every:
I have success to use sd_ecb_block function to encryption data. But I am not find how use this function to do decryption. Please teach me how to use this function...
I am trying to perform a simple ADC measurement using polling rather than using an interrupt. I have looked at examples and read the ADC section in the reference manual, but...
Hi Team,
Is there any way to enable/disable all interrupts?
Will BLE connection get disconnected because of this? If yes the what are the possible ways to
maintain the...
Hi,
I am new to all this,
I have just started using the nRF51822 evaluation kit.
I have manged to run the blinky example, however, eventhough I managed to download the...
After implement PWM (using pwm example at nRF51_SDK_8.0.0\examples\peripheral) into my BLE based nRF51422 project using SoftDevice S110, it has been working fine; however...
I want to add a command ordering by uart to make MCU entering Bootloader mode in app.
To achieve this function, I plan to use the two following example in SDK 8.0
ex1...
I am using nRf51822 series controller here i want to customize advertising request and other parameters, so i want to develop a radio code but without using stack. So can...
Hi,
We have being producing ble items with nrf51822 QFAAG , S110 SD 7.0, SDK 6.1, Dual bank DFU.
When updating the application throught Android, the bootloader hangs, because...
Any published document that helps with this? The folder structure seems to have changed significantly
This changelog isn't very specific
Using eclipse and gcc arm...
Since there is no examples folder with Keil 5.14 anymore, where do you place this repository so the links work? Trying to fix all the directory structures is very painful...
Hi,
I'm using the Taiyo Yuden nRF51822 module, which use a 32MHz crystal. Our team is still prototyping, so everything is still programmed and assembled by hand. On one of...
Hi,
I would like to know if it is possible that Android OS can know a specific device (has ever connected before) is advertising and OS notify a specific App to connect...
