Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi,
How to implement two sets of SPI on the NCS v3.0.0 nRF54L15 P2 port? If it can be achieved, please provide the corresponding IO ports for these two sets of SPI.
Kind...
I have been forced to upgrade to the nRF54L15 from the nRF52840 DK. The example code in the SDK for the nRF52840 the 'ble-peripheral' had example code for 'ble_app_uart' which...
Hello Nordic,
I’m using ncs\v3.1.0\nrf\samples\peripheral\radio_test` to test the nRF54L15 with PHY set to `NRF_RADIO_MODE_BLE_LR125KBIT`. However, the RF spectrum measurement...
Hello,
I am developing a custom board based on the nRF54L15.
Every time I do RTT connection from the extension i have been asked to prompt the target device (nRF54L15M33...
i working bare-metal, using HW registers directly.... no zephyr, no SDC....
i'm able to successfully receive packets through the RADIO RX path, but now want to add a timeout...
Hi,
After installing nrf sdk v2.9.3 trying to build application under Windows fails with the following message:
Trying to run any command inside the NCS shell/terminal...
With nrfconnect SDK V3.3.0 seeing commissioning issues with light bulb sample with nrf52840dk and google home. The logs are given below. Please help with resolution
Thanks...
Hi,
We have an application where we have a working DFU over BLE with SDK 2.9.1 but once we have migrated to 3.2.4 it has stopped working. Something has obviously changed...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hi, I am working with the nRF54L15 on sdk-nrf 3.2.3 and I am experiencing an unexpected behaviour with the NFC T4T stack regarding WTX frame timing.
Here is the observed...
Hi Nordic team,
I’m working on an nRF5340 project using MCUboot with the secondary slot placed on external flash.
I found a strange issue related to pm_static.yml . My...
Hello Team,
I am trying to test a PDM microphone (MP34DT01‑M MEMS) on the nRF9151 DK using nRF Connect SDK .
So far:
I have successfully tested I2C and I2S DAC audio...
The drag and drop programming was working fine on previous boards.
We just purchased 10 boards thinking that they were the same, but the don't seem to work.
PCA10040 3...
