Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
When opening a file that contains the packets that are transmitted in the BLE communication, the data is not observed.
Appears as shown below:
I installed the necessary...
Hello,
I am trying to add SoftDevice to our project which was non-SD for a year now, but I'm stuck with a problem.
I know that there are separate files for nrf_error.h...
In order to simply the creation of nRF softdevice projects, I'd like to make a suggestion. Rather than require the end-programmer to include dozens of individual include paths...
i changed the net-core flash partition and saved it to pm_static.yml. everything is ok while i build multi-image(mcuboot, cpuapp, b0n, cpunet) until my partner wants to build...
hello Nordic
i am working with nrf52840, zephyr rtos.
i can preform dfu via mcumgr cli (command line interface) or via nrfConnect application on my cell phone.
however...
Hi,
we are trying to use waveshare 2.9 epaper display with nrf52832, converted stm32 sample code to nrf52 with no luck. It seems we can not send command and data correctly...
Hi team ,
I am using 15.3 sdk and NRF52832 hardware. and Tool - SEGGER Embedded Studio for ARM 4.30c
I have developed code with DFU feature and and generated .hex file...
Hi,
I want to disable the UART of MCUBOOT to reduce power consumption. I searched in the DevZone and got the answer as below.
I followed the answer above, and created...
Hi there,
For the nRF5340, I read it support the Zigbee . So I just wanna know does it support the Zigbee frequency band in China, which is 780M?
Thanks,
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I know there is the following documentation. ・ SEGGER Embedded Studio Reference Manual : https://studio.segger...
Dear all
I'm using the SD s140 and nRF52840 along with one of the latest SDKs (17...). Everything works fine, I'm able to start advertising and connect, but from time to...
As the title says,
I combined the TWI function with the ble_app_uart example and the three i2c sensor communication was successful.
However, when I added SPI to develop...
Hello, I'm new to nRF Connect SDK.
I managed to add the blinky example to build. I added a custom board.
There is a prf.conf project file with just CONFIG_GPIO=y I'm now...
I'm trying to get the device ID of the lis3dh accelerometer on a Thingy:52
nrf_drv_twi_tx returns 3 as an error. This means NRF_ERROR_INTERNAL --> "If an error was detected...
Hello, when i try to flash my card, (nrf52840) in visual studio code i have those errors
ERROR: The file specified is not a valid hex file, has data outside valid areas...
