Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi,
I am trying to implement Zigbee mesh and read out the routing table of the local router. So far we achieved to get the device neighbor table by zb_zdo_mgmt_lqi_req...
Hello
Our application runs over nRF52840 + SDK16 + freeRTOS. While integrating libuarte library with our application we found an issue whereby if nrf_libuarte_async_init...
I am attempting to send 13 bytes over UARTE1 on the nRF52840. I'm using the ASYNC API in Zephyr. When I look at the output on an oscilloscope, some of the bytes show up in...
Hello, developers! I am wondering if the Light switch demo and the thingy52-mesh-provisioning-demo serve the same purpose. I tried to run them combined: the first one on an...
Hi,
I'm completely new in the nordic development area and I'm trying to read sensor data from a DHT22 Temperature and Humidity sensor.
I'm used to directly include libraries...
Hello:
I am working on a USB bootloader project. I am running into the issue where the USB will not boot on first start up but boots following this. I read some of the previous...
It appears that there is a bug in the antfs.c sample code in version 15.3.0
nRF5_SDK_15.3.0_59ac345\components\ant\ant_fs\antfs.c
It the transport_layer_cmd_decode(...
I have a custom board using nrf 52382 with NFC. While Developing application I have checked nRF52832 Revision 2 Errata .
I have a question related [218] NFCT: Frame Delay...
Hello,
Our application runs over nRF52840 + SDK16 + FreeRTOS and we are using libuarte application to drive the UART. We found that the app_timer_freertos.c doesn't provide...
Hello ,
When i am using sdk functions with freertos some of the callbacks/functions requires (for example) xTaskNotifyFromISR() instead of xTaskNotify .
So how can i decide...
I am going to mass-produce beacons with built-in ble uart app sample.
However, I am not sure those produced beacons will have unique mac-address.
In my view, those are...
Hi all i am trying make a communication between esp32 and nrf52840 using UART. Initializing the uart driver was proper and pins also correct. when nrf start transmits then...
Using nrf52810 SDK 17 ble_app_hrs for my example, and i add some code about the passkey
Now the situation is after I enter the passkey on my Iphone nRFconnect app, and if...
