I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I want to build my own board configuration:
The default configuration of the board is as follows: ncs?v1.2.0,zephyr?boards?arm?nrf9160_pca10090
How do I generate my own...
Hello
I'm using NRF connect the app to perform read and write on nrf52840 board SDK ver of 15.0.0.
I can perform the write and read operations using nrf connect app, and...
Hi
I'm working on a custom PCB based on nRF52840 soc and SDK version 16.0
currently I'm trying to interface my MCU with an external flash of model MT25QL01GBBB
my...
Hi,
I would like to interface ICM20948 with nrf52832 and communicate over TWI or SPI. That thing I don't understand is the logic voltage of the bus. In nrf52 specifications...
Hello,
I went through the instructions in the Getting Started Assistant to setup nRF Connect SDK for Linux but I am getting the following error when trying to build a project...
Hi,
I am programming nRF52840 dev kit (SDK16) as a peripheral with S140. Smartphone is central.
data needs to be transferred between both.
I need the dev kit to consume...
Hello, I’m using nRF52840 with SDK 16 and SD 7. My purpose is to save as much power is possible using high-frequency clock (32MHz) only during periodic duties and BLE activity...
What are best practices for updating an nRF52832 via UART from an nRF52840? There seem to be at least two problems to solve:
Transmitting the 832 image via BLE to the...
Hello,
I'm measuring the idle current using a PCA10040 DK, SDK v16.
Finding that the idle current is about 3uA (which I think is correct) after any debug operation like...
Our setup is using a NRF52832 with SDK15.0.0.
While working with a time sensitive external circuit where we both sample the state of the GPIO and enable LDETECT on it...
I have just received my nRF52 development board and I have tried to program one of the pre-bjui;t examples (Blinky). The USB drive on the board appears and if I drag the hex...
Hi,
I'm using an application with FreeRTOS , nRF52833, SDK 16.
When I'm trying to get it into low power (sleep mode) the system still consumes ~4mA
In vPortSuppressTicksAndSleep...
Hi,
I am starting with PPK. Tried some measurements on ble examples and looks like i am doing something wrong. I have aproximatelly 7mA during advertising. Am I doing something...
Hi,
i have load existing program to new nRF52 module. But it shows NRF_ERROR_NO_MEM.
Same old module doesn't show this error. i also reload the soft device. But no improvement...
I'm looking to implement the following security schema:
The peripheral does not have a display nor input capabilities
A smartphone will connect to the device
The peripheral...
